 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| ADVANCED COMMUNCIATIONS Description The ACS8510 is a highly integrated, single-chip solution for the Synchronous Equipment Timing Source (SETS) function in a SONET or SDH Network Element. The device generates SONET or SDH Equipment Clocks (SEC) and frame synchronization clocks. The ACS8510 is fully compliant with the required specifications and standards. The device supports Free-Run, Locked and Holdover modes. It also supports all three types of reference clock source: recovered line clock, PDH network, and node synchronization. The ACS8510 generates independent SEC and BITS clocks, an 8 kHz Frame Synchronization clock and a 2 kHz Multi-Frame Synchronization clock. Two ACS8510 devices can be used together in a Master/Slave configuration mode allowing system protection against a single ACS8510 failure. A microprocessor port is incorporated, providing access to the configuration and status registers for device setup and monitoring. The ACS8510 supports IEEE 1149.1 JTAG boundary scan. * Meets Holdover requirements, lowest bandwidth 0.1 Hz. Synchronous Equipment Timing Source for SONET or SDH Network Elements FINAL Features Suitable for Stratum 3E*, 3, 4E and 4 SONET or SDH Equipment Clock (SEC) applications Meets AT&T, ITU-T, ETSI and Telcordia specifications Accepts 14 individual input reference clocks Generates 11 output clocks Supports Free-Run, Locked and Holdover modes of operation Robust input clock source quality monitoring on all inputs Automatic hit-less source switchover on loss of input Phase build-out for output clock phase continuity during input switchover and mode transitions Microprocessor interface - Intel, Motorola, Serial, Multiplexed, EEPROM Programmable wander and jitter tracking/ attenuation 0.1 Hz to 20 Hz Support for Master/Slave device configuration alignment and hot/standby redundancy IEEE 1149.1 JTAG Boundary Scan Single 3.3 v operation. 5 v I/O compatible Operating temperature (ambient) -40C to +85C Available in 100 pin LQFP package ACS8510 SETS Block Diagram 14 Inp ut Reference Source includin g: AM I 64/8 kHz 2 kHz 8 kHz N x 8 kHz 1.544 MHz 2.048 MHz 6.48 MHz 19.44 MHz 25.92 MHz 38.88 MHz 51.84 MHz 77.76 MHz 155.52 MHz Input Ports TOUT4 selector Div ider PFD Dig ital Loop Filter Output Ports DTO 2xT OUT4 6xT IN1 4xT IN2 4xT IN3 TOUT0 selector MFrSync Monitors DPLL/F req. Synthesis 7xT OUT0 PFD Div ider Dig ital Loop Filter DTO APLL Frequency Dividers DPLL/Freq. S ynthesis T CK TDI TMS T RST TDO MFrSync FrSync 11 Outp ut Ports includin g: 1.544/2.048 M Hz 3.088/4.096 M Hz 6.176/8.182 M Hz 12.352/16.384 M Hz 6.48 MHz 19.44 MHz 25.92 MHz 38.88 MHz 51.84 MHz 77.76 MHz 155.52 MHz 311.04 MHz AM I 64/8 kHz 2 kHz MFrSy nc 8 kHz FrSy nc IEEE 1149.1 JTAG Chip C lock Generator Priority Table Register Set Micropro cessor Port TCXO (*OCXO) CLK Revision 2.07/Jan 2001 a2001 Semtech Corp www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS Table of Contents Pin diagram................................................................................................................................................3 Pin descriptions.........................................................................................................................................4 Functional description...............................................................................................................................7 Local oscillator clock..........................................................................................................................................................8 Input Interfaces..................................................................................................................................................................8 Over voltage protection.......................................................................................................................................................8 Input reference clock ports................................................................................................................................................9 Input wander and jitter tolerance...................................................................................................................................11 Output clock ports...........................................................................................................................................................13 Output wander and jitter..................................................................................................................................................14 Phase variation.................................................................................................................................................................16 Phase build-out.................................................................................................................................................................17 Microprocessor interface................................................................................................................................................17 Interrupt enable and clear...............................................................................................................................................19 Register map description.................................................................................................................................................21 Register map description.................................................................................................................................................25 Selection of input reference clock source.....................................................................................................................33 Clock quality monitoring..................................................................................................................................................34 Activity monitoring...........................................................................................................................................................35 Modes of operation..........................................................................................................................................................38 Protection facility.............................................................................................................................................................39 JTAG..............................................................................................................................................................................42 Power on reset - PORB.....................................................................................................................................................42 Electrical specification............................................................................................................................45 Absolute maximum range...............................................................................................................................................45 Operating conditions.......................................................................................................................................................45 TTL DC characterisitics...................................................................................................................................................45 PECL DC characteristics..................................................................................................................................................47 LVDS DC characteristics..................................................................................................................................................48 AMI DC characteristics....................................................................................................................................................49 Jitter characteristics........................................................................................................................................................52 JTAG timing........................................................................................................................................................................55 Microprocessor interface timing characteristics.......................................................................................56 Motorola mode..................................................................................................................................................................56 Intel mode................................................................................................................................................................58 Multiplexed mode.............................................................................................................................................................60 Serial mode.......................................................................................................................................................................62 EEPROM mode.................................................................................................................................................................64 Package information................................................................................................................................65 Application information............................................................................................................................67 Simplified application schematic...................................................................................................................................67 Revision History.......................................................................................................................................68 Order information....................................................................................................................................69 Revision 2.07/Jan 2001 a2001 Semtech Corp 2 www.semtech.com FINAL ACS8510 SETS ADVANCED COMMUNCIATIONS Pin Diagram FINAL 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 AGND TRST IC NC AGND VA1+ TMS INTREQ TCK REFCLK DGND VD+ VD+ DGND DGND VD+ NC SRCSW VA2+ AGND TDO IC TDI I1 I2 VAMI+ TO8NEG TO8POS GND_AMI FrSync MFrSync GND_DIFF VDD_DIFF TO6POS TO6NEG TO7POS TO7NEG GND_DIFF VDD_DIFF I5POS I5NEG I6POS I6NEG VDD5 SYNC2K I3 I4 I7 DGND VDD 1 SDH/SONET SETS Rev 2.x ACS8510 Figure 1: Top view of 100 pin LQFP package. NC - Not Connected; leave to Float. IC - Internally Connected; leave to Float. 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 SONSDHB MSTSLVB IC IC IC TO9 TO5 TO4 DGND VDD TO3 TO2 TO1 DGND VDD VDD DGND AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 RDY PORB ALE RDB WRB CSB A0 A1 A2 A3 A4 A5 A6 DGND VDD UPSEL0 UPSEL1 UPSEL2 I14 I13 I12 I11 I10 I9 I8 Revision 2.07/Jan 2001 a2001 Semtech Corp 3 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS Pin Descriptions Power PIN 12, 13, 16 26 33, 39 FINAL SYM B OL VD+ VAMI+ VDD_DIFF IO P P P T YPE - N A M E /DE SCR I P T I O N S u p p l y v ol t ag e: Digital sup p ly to gates in analog section, +3.3 Volts. +/- 10% S u p p l y v ol t ag e : Digital sup p ly to AMI outp ut, +3.3 Volts. +/- 10% S u p p l y v ol t ag e : Digital sup p ly for differential p or ts, +3.3 Volts. +/- 10% V D D 5: Digital sup p ly for +5 Volts tolerance to inp ut p ins. Connect to +5 volts (+/- 10%) for clamp ing to +5 v. Connect to VDD for clamp ing to +3.3 v. Leave floating for no clamp ing, inp ut p ins tolerant up to +5.5 v. S u p p l y v ol t ag e : Digital sup p ly to logic, +3.3 Volts. +/- 10% S u p p l y v ol t ag e: Analog sup p ly to clock multip ying PLL, +3.3 Volts. +/- 10% S u p p l y v ol t ag e : Analog sup p ly to outp ut PLL, +3.3 Volts. +/- 10% S u p p l y G r ou n d : Digital ground for logic 44 VDD5 P - 50, 61, 85, 86, 91 6 19 11, 14, 15, 49, 62, 84, 87, 92 29 32, 38 1, 5, 20 VDD VA1+ VA2+ DGN D P P P P - GN D_AMI GN D_DIFF AGN D P P P - S u p p l y G r ou n d : Digital ground for AMI outp ut S u p p l y G r ou n d : Digital ground for differential p or ts S u p p l y G r ou n d : Analog ground No connections PIN 4, 17 3, 22, 96, 97,98 SYM B OL NC IC IO - T YPE - N A M E /DE SCR I P T I O N N ot C on n ect ed : Leave to Float I n t er n al l y C on n ect ed : Leave to Float Note: I = input, O = output, P = power, TTLU = TTL input with pull-up resistor, TTLD = TTL input with pull-down resistor Revision 2.07/Jan 2001 a2001 Semtech Corp 4 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS Others PIN 2 FINAL N A M E /DE SCR I P T I O N J TA G C o n t r o l R e se t I n p u t : TRST = 1 to enab le JTA G Bound ary Scan mod e. TRST = 0 for normal d evice op eration (JTA G logic transp arent). If not used connect to GN D or leave floating. J TA G Te st M o d e S e l e ct : Bound ary Scan enab le. Samp led on rising ed ge of TCK. If not used connect to V DD or leave floating. I n t e r r u p t R e q u e st : A ctive h igh softw are Interrup t outp ut J TA G C l o ck : Bound ary Scan clock inp ut. If not used connect to GN D or leave floating. Th is p in may req uire a cap acitor p laced b etw een th e p in and th e nearest GN D, to red uce noise p ickup . A value of 10 p F sh ould b e ad eq uate, b ut th e value is d ep end ent on PCB layout. R e f e r e n ce C l o ck : 12.8 MHz (refer to section h ead ed Local Oscillator Clock) S o u r ce S w i t ch i n g : Force Fast Source Sw itch ing J TA G O u t p u t : Serial test d ata outp ut. Up d ated on falling ed ge of TCK. If not used leave floating. J TA G I n p u t : Serial test d ata Inp ut. Samp led on rising ed ge of TCK. If not used connect to V DD or leave floating. I n p u t r e f e r e n ce 1: comp osite clock 64 kHz + 8 kHz I n p u t r e f e r e n ce 2: comp osite clock 64 kHz + 8 kHz O u t p u t r e f e r e n ce 8: comp osite clock, 64 kHz + 8 kHz negative p ulse O u t p u t r e f e r e n ce 8: comp osite clock, 64 kHz + 8 kHz p ositive p ulse O u t p u t r e f e r e n ce 10: 8 kHz Frame Sync clock outp ut (sq uare w ave) O u t p u t r e f e r e n ce 11: 2 kHz Multi-Frame Sync clock outp ut (sq uare w ave) O u t p u t r e f e r e n ce 6: d efault 38.88 MHz. A lso Dig1 (1.544 MHz/2.048 MHz and 2, 4, 8 x), 19.44 MHz, 155.52 MHz, 311.04 MHz. Default typ e LV DS. O u t p u t r e f e r e n ce 7: d efault 19.44 MHz. A lso 51.84 MHz, 77.76 MHz, 155.52 MHz. Default typ e PECL. I n p u t r e f e r e n ce 5: d efault 19.44 MHz, d efault typ e LV DS I n p u t r e f e r e n ce 6: d efault 19.44 MHz, d efault typ e PECL 5 www.semtech.com SYM B OL TRST IO I T YPE T T LD 7 8 T MS IN T R E Q I O T T LU TTL CMOS 9 TCK I T T LD 10 18 21 23 24 25 27 28 30 31 34 35 36 37 40 41 42 43 REFCLK SRCSW TDO TDI I1 I2 TO8N EG TO8POS FrSync MFrSync TO6POS TO6N EG TO7POS TO7N EG I5POS I5N EG I6POS I6N EG I I O I I I O O O O TTL T T LD TTL CMOS T T LU A MI A MI A MI A MI TTL CMOS TTL CMOS PECL/ LV DS LV DS/ PECL LV DS PECL PECL LV DS O O I I Revision 2.07/Jan 2001 a2001 Semtech Corp ACS8510 SETS ADVANCED COMMUNCIATIONS PIN 45 46 47 48 51 52 53 54 55 56 57 58 - 60 63 - 69 70 FINAL N A M E /DE SCR I P T I O N S y n ch r o n i se 2 k H z : Connect to 2 kHz Multi-Frame Sync outp ut of p ar tner A CS8510 in red und ancy system I n p u t r e f e r e n ce 3: p rogrammab le, d efault 8 kHz I n p u t r e f e r e n ce 4: p rogrammab le, d efault 8 kHz I n p u t r e f e r e n ce 7: p rogrammab le, d efault 19.44 MHz I n p u t r e f e r e n ce 8: p rogrammab le, d efault 19.44 MHz I n p u t r e f e r e n ce 9: p rogrammab le, d efault 19.44 MHz I n p u t r e f e r e n ce 10: p rogrammab le, d efault 19.44 MHz. I n p u t r e f e r e n ce 11: p rogrammab le, d efault (master mod e)1.544/2.048 MHz, d efault (slave mod e) 6.48 MHz I n p u t r e f e r e n ce 12: p rogrammab le, d efault 1.544/2.048 MHz. I n p u t r e f e r e n ce 13: p rogrammab le, d efault 1.544/2.048 MHz. I n p u t r e f e r e n ce 14: p rogrammab le, d efault 1.544/2.048 MHz. M i cr o p r o ce sso r se l e ct : Configures th e inter face for a p ar ticular microp rocessor typ e. M i cr o p r o ce sso r I n t e r f ace A d d r e ss: A d d ress b us for th e microp rocessor inter face registers. A (0) is SDI in Serial mod e. C h i p S e l e ct ( A ct i v e L o w ) : Th is p in is asser ted Low b y th e microp rocessor to enab le th e microp rocessor inter face. W r i t e ( A ct i v e L o w ) : Th is p in is asser ted Low b y th e microp rocessor to initiate a w rite cycle. In Motorola mod e, WRB = 1 for Read . R e ad ( A ct i v e L o w ) : Th is p in is asser ted Low b y th e microp rocessor to initiate a read cycle. A d d r e ss L at ch E n ab l e : Th is p in b ecomes th e ad d ress latch enab le from th e microp rocessor. Wh en th is p in transitions from High to Low, th e ad d ress b us inp uts are latch ed into th e internal registers. A LE = SCLK in Serial mod e. P o w e r O n R e se t : Master reset. If PORB is forced Low, all internal states are reset. b ack to d efault values. R e ad y / D at a ack n o w l e d g e : Th is p in is asser ted High to ind icate th e d evice h as comp leted a read or w rite op eration. A d d r e ss/ D at a: Multip lexed d ata/ad d ress b us d ep end ing on th e microp rocessor mod e selection. A D(0) is SDO in Serial mod e 6 www.semtech.com SYM B OL SYN C2K I3 I4 I7 I8 I9 I10 I11 I12 I13 I14 UPSEL(2:0) A (6:0) CSB IO I I I I I I I I I I I I I I T YPE T T LD T T LD T T LD T T LD T T LD T T LD T T LD T T LD T T LD T T LD T T LD T T LD T T LD T T LU 71 WRB I T T LU 72 RDB I T T LU 73 A LE I T T LD 74 75 76 - 83 PORB RDY A D(7:0) I O IO T T LU TTL CMOS T T LD Revision 2.07/Jan 2001 a2001 Semtech Corp ACS8510 SETS ADVANCED COMMUNCIATIONS PIN 88 89 90 93 94 95 FINAL N A M E /DE SCR I P T I O N O u t p u t r ef er en ce 1: default 6.48 MHz. Also Dig1 (1.544 MHz/2.048 MHz and 2, 4, 8 x), 19.44 MHz, 25.92 MHz O u t p u t r ef er en ce 2: default 38.88 MHz. Also Dig2 (1.544 MHz/2.048 MHz and 2, 4, 8 x), 25.92 MHz, 51.84 MHz O u t p u t r ef er en ce 3: 19.44 MHz - fixed. O u t p u t r ef er en ce 4: 38.88 MHz - fixed. O u t p u t r ef er en ce 5: 77.76 MHz - fixed. O u t p u t r ef er en ce 9: 1.544/2.048 MHz. (T4 BITS) M A S T E R S L AV E B : Master slave select: sets the initial p ow er up state (or state after a PORB) of the Master/Slave selection register, addr 34, b it 1. The register state can b e changed after p ow er up b y softw are. S O N E T S D H B : SON ET or SDH frequency select: sets the initial p ow er up state (or state after a PORB) of the SON ET/SDH frequency selection registers, addr 34h, b it 2 and addr 38, b it 5. The register states can b e changed after p ow er up b y softw are. SYM B OL TO1 TO2 TO3 TO4 TO5 TO9 IO O O O O O O T YPE TTL CMOS TTL CMOS TTL CMOS TTL CMOS TTL CMOS TTL CMOS 99 MSTSLVB I TTL U 100 SON SDHB I T T LD Functional description The ACS8510 is a highly integrated, single-chip solution for the SETS function in a SONET/SDH Network Element, for the generation of SEC and frame synchronisation pulses. In Free-Run mode, the ACS8510 generates a stable, lownoise clock signal from an internal oscillator. In Locked mode, the ACS8510 selects the most appropriate input reference source and generates a stable, low-noise clock signal locked to the selected reference. In Holdover mode, the ACS8510 generates a stable, low-noise clock signal from the internal oscillator, adjusted to match the last-known-good frequency of the last-selected reference source. In all modes, the frequency accuracy, jitter and drift performance of the clock meet the requirements of ITU G.812, G.813, G.823, GR 1244-CORE. Revision 2.07/Jan 2001 a2001 Semtech Corp 7 The ACS8510 supports all three types of reference clock source: recovered line clock (TIN1), PDH network synchronisation timing (TIN2) and node synchronisation (TIN3). The ACS8510 generates independent TOUT0 and TOUT4 clocks, an 8 kHz Frame Synchronisation clock and a 2 kHz Multi-Frame Synchronisation clock. The ACS8510 has a high tolerance to input jitter and wander. The output jitter and wander are low, where the wander transfer is programmable (0.1 Hz up to 20 Hz cut-off points). The ACS8510 supports protection. Two ACS8510 devices can be configured to provide protection against a single ACS8510 failure. The protection maintains alignment of the two ACS8510 devices (Master and Slave) and ensures that both ACS8510 devices maintain the same priority table, choose the same www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS reference input and generate the TOUT0 clock, the 8 kHz Frame Synchronisation clock and the 2 kHz Multi-Frame Synchronisation clock with the same phase. The ACS8510 includes a microprocessor port, providing access to the configuration and status registers for device setup and monitoring. Local Oscillator Clock The Master system clock on the ACS8510 should be provided by an external clock oscillator of frequency 12.80 MHz. The clock specification is important for meeting the ITU/ETSI and Telcordia performance requirements in Holdover mode. ITU and ETSI specifications permit a combined drift characteristic, at constant temperature, of all non-temperature-related parameters, of up to 10 ppb per day. The same specifications allow a drift of 1 ppm over a temperature range of 0 to 70 Celsius. Telcordia specifications are somewhat tighter, requiring a non-temperature-related drift of less than 40 ppb per day and a drift of 280 ppb over the temperature range 0 to 50 Celsius. ITU and ETSI specification Tolerance: Drift*: +/- 4.6 ppm over 20 year life time. +/- 0.05 ppm/15 seconds @ constant temp. +/- 0.01 ppm/day @ constant temp. +/- 1 ppm over temp. range 0-70 Celsius *Frequency drift over supply voltage range of 2.7 V to 3.3 V. FINAL Crystal Frequency Calibration The absolute crystal frequency accuracy is less important than the stability since any frequency offset can be compensated by adjustment of register values in the IC. This allows for calibration and compensation of any crystal frequency variation away from its nominal value. +/- 50 ppm adjustment would be sufficient to cope with most crystals, in fact the range is an order of magnitude larger due to the use of two 8 bit register locations. The setting of the conf_nominal_frequency register allows for this adjustment. An increase in the register value increases the output frequencies by 0.02 ppm for each LSB step. The default value (in decimal) is 39321. The minimum being 0 and the maximum 65535, gives a +500 ppm to -700 ppm adjustment range of the output frequencies. For example, if the crystal was oscillating at 12.8 MHz + 5 ppm, then the calibration value in the register to give a -5 ppm adjustment in output frequencies to compensate for the crystal inaccuracy, would be : 39321 - (5 / 0.02) = 39071 (decimal). Input Interfaces The ACS8510 supports up to fourteen input reference clock sources from input types TIN1, TIN2 and TIN3 using TTL, CMOS, PECL, LVDS and AMI buffer I/O technologies. These interface technologies support 3.3 V and 5 V operation. Over-Voltage Protection The ACS8510 may require Over-Voltage Protection on input reference clock ports according to the ITU Recommendation K.41. Semtech recommends the use of their protection devices for this purpose (see separate Semtech data book). Telcordia GR-1244 CORE specification Tolerance: Drift*: +/- 4.6 ppm over 20 year life time. +/- 0.05 ppm/15 seconds @ constant temp. +/- 0.04 ppm/day @ constant temp. +/- 0.28 ppm over temp. range 0-50 Celsius *Frequency drift over supply voltage range of 2.7 V to 3.3 V. Please contact Semtech for information on crystal oscillator suppliers. Revision 2.07/Jan 2001 a2001 Semtech Corp 8 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS Input Reference Clock Ports Table 1 gives details of the input reference ports, showing the input technologies and the range of frequencies supported on each port; the default spot frequencies and default priorities assigned to each port on power-up or by reset are also shown. Note that SDH and SONET networks use different default frequencies; the network type is pin-selectable (using the SONSDHB pin). Specific frequencies and priorities are set by configuration. Although each input port is shown as belonging to one of the types, TIN1, TIN2 or TIN3, they are fully interchangeable as long as the selected speed is within the maximum operating speed of the input port technology. SDH and SONET networks use different default frequencies; the network type is selectable using the config_mode register 34 Hex, bit 2. For SONET, config_mode register 34 Hex, bit 2 = 1, for SDH config_mode register 34 Hex, bit 2 = 0. On power-up or by reset, the default will be set by the state of the SONSDHB pin (pin 100). Specific frequencies and priorities are set by configuration. TTL ports (compatible also with CMOS signals) support clock speeds up to 100 MHz, with the highest spot frequency being 77.76 MHz. The actual spot frequencies supported are; 8 kHz (and N x 8 kHz), 1.544 MHz/2.048 MHz, 6.48 MHz, 19.44 MHz, 25.92 MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz. The frequency selection is programmed via the cnfg_ref_source_frequency register. The internal DPLL will normally lock to the selected input at the frequency of the input, eg. 19.44 MHz will lock the DPLL phase comparisons at 19.44 MHz. It is, however, possible to utilise an internal pre-divider to the DPLL to divide the input frequency before it is used for phase comparisons in the DPLL. This pre-divider can be used in one of 2 ways: Revision 2.07/Jan 2001 a2001 Semtech Corp 9 FINAL (i) any of the supported spot frequencies can be divided to 8 kHz by setting the "lock8K" bit (bit 6) in the appropriate cnfg_ref_source_frequency register location (ii) any multiple of 8 kHz between 1544 kHz to 100 MHz can be supported by using the "DivN" feature (bit 7 of the cnfg_ref_source_frequency register). Any reference input can be set to use DivN independently of the frequencies and configurations of the other inputs. Any reference input with the "DivN" bit set in the cnfg_ref_source_frequency register will employ the internal pre-divider prior to the DPLL locking. The cnfg_freq_divn register contains the divider ratio N where the reference input will get divided by (N+1) where 0 ACS8510 SETS ADVANCED COMMUNCIATIONS P or t N u m b er I_1 FINAL Fr eq u en ci es S u p p or t ed 64/8kHz (comp osite clock, 64kHz + 8kHz) Default (SON ET): 64/8kHz Default (SDH): 64/8kHz 64/8kHz (comp osite clock, 64kHz + 8kHz) Default (SON ET): 64/8kHz Default (SDH): 64/8kHz Up to 100MHz (see N ote 1) Default (SON ET): 8kHz Default (SDH): 8kHz Up to 100MHz (see N ote 1) Default (SON ET): 8kHz Default (SDH): 8kHz Up to 155.52MHz (see N ote 2) Default (SON ET): 19.44MHz Default (SDH): 19.44MHz Up to 155.52MHz (see N ote 2) Default (SON ET): 19.44MHz Default (SDH): 19.44MHz Up to 100MHz (see N ote 1) Default (SON ET): 19.44MHz Default (SDH): 19.44MHz Up to 100MHz (see N ote 1) Default (SON ET): 19.44MHz Default (SDH): 19.44MHz Up to 100MHz (see N ote 1) Default (SON ET): 19.44MHz Default (SDH): 19.44MHz Up to 100MHz (see N ote 1) Default (SON ET): 19.44MHz Default (SDH): 19.44MHz Up to 100MHz (see N ote 1) Default (Master) (SON ET): 1.544MHz Default (Master) (SDH): 2.048MHz Default (Slave) 6.48MHz Up to 100MHz (see N ote 1) Default (SON ET): 1.544MHz Default (SDH): 2.048MHz Up to 100MHz (see N ote 1) Default (SON ET): 1.544MHz Default (SDH): 2.048MHz Up to 100MHz (see N ote 1) Default (SON ET): 1.544MHz Default (SDH): 2.048MHz C h an n e l N u m b er 0001 P or t Ty p e T IN 3 I n p u t P or t Te c h n o l o g y A MI D e f au l t P ri ori t y 2 I_2 0010 T IN 3 A MI 3 I_3 0011 T IN 3 TTL/CMOS 4 I_4 0100 T IN 3 TTL/CMOS 5 I_5 0101 T IN 1 LVDS/PECL LVDS default PECL/LVDS PECL default 6 I_6 0110 T IN 1 7 I_7 0111 T IN 1 TTL/CMOS 8 I_8 1000 T IN 1 TTL/CMOS 9 I_9 1001 T IN 1 TTL/CMOS 10 I_10 1010 T IN 1 TTL/CMOS 11 I_11 1011 T IN 2 TTL/CMOS 12/1 (N ote 3) I_12 1100 T IN 2 TTL/CMOS 13 I_13 1101 T IN 2 TTL/CMOS 14 I_14 1110 T IN 2 TTL/CMOS 15 Table 1: Input Reference Source Selection and Priority Table Revision 2.07/Jan 2001 a2001 Semtech Corp 10 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS Notes for Table 1. Note 1: TTL ports (compatible also with CMOS signals) support clock speeds up to 100 MHz, with the highest spot frequency being 77.76 MHz. The actual spot frequencies are: 2 kHz, 4 kHz, 8 kHz, 1.544 MHz/2.048 MHz, 6.48 MHz, 19.44 MHz, 25.92 MHz, 38.88 MHz, 51.84 MHz, 77.76 MHz. There are different output clock frequencies available for SONET and SDH applications. SONSDHB controls the default frequency output. F1/F2 means that the output frequency is F1 when the SONSDHB pin is High and F2 when SONSDHB pin is Low. Note 2: PECL and LVDS ports support the spot clock frequencies listed above plus 155.52 MHz and 311.04 MHz. Note 3: Input port FINAL DivN examples To lock to 2.000 MHz. (1) The cnfg_ref_source_frequency register is set to 11XX0001 (binary) to set the DivN, lock8k bits, and the frequency to E1/T1. (XX = leaky bucket ID for this input). (2) The cnfg_mode register (34Hex) bit 2 needs to be set to 1 to select SONET frequencies (T1). (3) The frequency monitors are disabled in cnfg_monitors register (48Hex) by writing 00 to bits 0 and 1. (4) the DivN register is set to F9 Hex (249 decimal). To lock to 10.000 MHz. (1) The cnfg_ref_source_frequency register is set to 11XX0010 (binary) to set the DivN, lock8k bits, and the frequency to 6.48 MHz. (XX = leaky bucket ID for this input). (2) The frequency monitors are disabled in cnfg_monitors register (48Hex) by writing 00 to bits 0 and 1. (3) the DivN register is set to 4E1 Hex (1249 decimal). An AMI port supports a composite clock, consisting of a 64 kHz AMI clock with 8 kHz boundaries marked by deliberate violations of the AMI coding rules, as specified in ITU recommendation G.703. Departures from the nominal pattern are detected within the ACS8510, and may cause reference-switching if too frequent. See Figure 9 for more details. Input Wander and Jitter Tolerance The ACS8510 is compliant to the requirements of all relevant standards, principally ITU Recommendation G.825, ANSI T1.101-1994 and ETS 300 462-5 (1997). All reference clock inputs have a tight frequency tolerance but a generous jitter tolerance. PullRevision 2.07/Jan 2001 a2001 Semtech Corp 11 in, hold-in and pull-out ranges are specified for each input port in Table 2. Minimum jitter tolerance masks are specified in Figures 1 and 2, and Tables 3 and 4, respectively. The ACS8510 will tolerate wander and jitter components greater than those shown in Figure 1 and Figure 2, up to a limit determined by a combination of the apparent long-term frequency offset caused by wander and the eye-closure caused by jitter (the input source will be rejected if the offset pushes the frequency outside the hold-in range for long enough to be detected, whilst the signal will also be rejected if the eye closes sufficiently to affect the signal purity). The 8klocking mode should be engaged for high jitter tolerance according to these masks. All reference clock www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS ports are monitored for quality, including frequency offset and general activity. Single short-term interruptions in selected reference clocks may not cause rearrangements, whilst longer interruptions, or multiple, short-term interruptions, will cause rearrangements, as will frequency offsets which are sufficiently large or sufficiently long to cause loss-of-lock in the phase-locked loop. The failed reference source will be removed from the priority table and declared as unserviceable, until its perceived quality has been restored to an acceptable level. The registers reg sts_curr_inc_offset (address 0C, 0D, 07) report the frequency of the DPLL FINAL with respect to the external TCXO frequency. This is a 19 bit signed number with one LSB representing 0.0003 ppm (range of +/- 80 ppm). Reading this regularly can show how the currently locked source is varying in value e.g. due to wander on its input. The ACS8510 performs automatic frequency monitoring with an acceptable input frequency offset range of +/- 16.6 ppm. The ACS8510 DPLL has a programmable frequency limit of +/- 80 ppm. If the range is programmed to be > 16.6 ppm, the frequency monitors should be disabled so the input reference source is not automatically rejected as out of frequency range. J i t t er To l e r a n c e G.703 G.783 G.823 GR-1244-CORE Fr eq u en cy M on i t or A c c e p t an c e R an g e Fr eq u en cy A c c e p t an c e R an g e ( Pull-in) +/- 4.6 p p m (see N ote 1) +/- 9.2 p p m (see N ote 2) Fr eq u en cy A c c e p t an c e R an g e ( H o l d - i n ) +/- 4.6 p p m (see N ote 1) +/- 9.2 p p m (see N ote 2) Fr eq u en cy A c c e p t an c e R an g e ( P u l l - ou t ) +/- 4.6 p p m (see N ote 1) +/- 9.2 p p m (see N ote 2) +/- 16.6 p p m Table 2: Input Reference Source Jitter Tolerance. Notes for Table 2. Note 1. The frequency acceptance and generation range will be +/-4.6 ppm around the required frequency when the external crystal frequency accuracy is within a tolerance of +/- 4.6 ppm. Note 2. The fundamental acceptance range and generation range is +/- 9.2 ppm with an exact external crystal frequency of 12.8 MHz. Note 3. The power up default PDLL range is as stated in note 2, but the range is also programmable from 0 to 80 ppm in 0.08 ppm steps. Revision 2.07/Jan 2001 a2001 Semtech Corp 12 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS FINAL $ $ $ $ $ I I I I I -LWWHU DQG ZDQGHU IUHTXHQF\ ORJ VFDOH I I I I Figure 1: Minimum Input Jitter Tolerance for inputs supporting G.783 compliant sources ST M l evel P e ak t o p e ak am p l i t u d e ( u n i t I n t e r v al ) A0 2800 A1 311 A2 39 A3 1.5 A4 0.15 F0 12u F1 178u F2 1.6m F3 15.6m Fr eq u en cy ( H z ) F4 0.125 F5 19.3 F6 500 F7 6.5k F8 65k F9 1.3m STM-1 Table 3: Amplitude and Frequency values for Jitter Tolerance for inputs supporting G.783 compliant sources Output Clock Ports The device supports a set of main output clocks, TOUT0 and TOUT4, and a pair of secondary output clocks, 'Frame-Sync' and 'Multi-Frame-Sync'. The two main output clocks, T OUT0 and TOUT4, are independent of each other and are individuallyselectable. The two secondary output clocks, 'Frame-Sync' and 'Multi-Frame-Sync', are derived from TOUT0. The frequencies of the output clocks are selectable from a range of pre-defined spot frequencies and a variety of output technologies are supported, as defined in Table 5. Performance-wise, the output ports are specified in Figures 3, 4 and 5, in terms of jitter, MTIE (and TDEV) and Phase Error, respectively. Low-speed Output Clock (T OUT4 ) The TOUT4 clock is supplied on two output ports, TO8 and TO9. The former port will provide an AMI signal carrying a composite clock of 64 kHz and 8 kHz, according to ITU Recommendation G.703. The latter port will provide a TTL/CMOS signal at either 1.544 MHz or 2.048 MHz, depending on the setting of the SONSDHB pin. High-speed Output Clock (Part of T OUT0) The TOUT0 port has multiple outputs. Outputs TO1 and TO2 are TTL/CMOS output with a choice of 11 different frequencies up to 51.84 MHz. Outputs TO3 to TO5 are all TTL/CMOS outputs with fixed frequencies of 19.44 MHz, 38.88 MHz and 77.76 MHz, respectively. Output TO6 is differential and can support clocks up to 155.52 MHz. Output TO7 is also differential www.semtech.com Revision 2.07/Jan 2001 a2001 Semtech Corp 13 ACS8510 SETS ADVANCED COMMUNCIATIONS FINAL 3HDNWRSHDN MLWWHU DQG ZDQGHU DPSOLWXGH ORJ VFDOH $ $ -LWWHU DQG ZDQGHU IUHTXHQF\ ORJ VFDOH I I I I Figure 2: Minimum Input Jitter Tolerance for inputs supporting G.703 compliant sources Ty p e S p ec. A mp litud e ( U I p k-p k) A1 DS1 E1 G R - 1244- C O R E I T U G. 823 5 1.5 A2 0.1 0.2 F1 10 20 Fr e q u e n cy ( Hz ) F2 500 2.4k F3 8k 18k F4 40k 100k Table 4: Amplitude and Frequency values for Jitter Tolerance for inputs supporting G.703 compliant sources and can support clocks up to 155.52 MHz. Each output is individually configured to operate at the frequencies shown in Table 5 (configuration must be consistent between ACS8510 devices for protection-switching to be effective - output clocks will be phase-aligned between devices). Using the cnfg_differential_outputs register, outputs TO6 and T O7 can be made to be LVDS or PECL compatible. Frame Sync and Multi-Frame Sync Clocks (Part of T OUT0) These will be driven from the TOUT0 clock. They will be synchronised with their counterparts in a second ACS8510 device (if used), using the technique described later. Output Wander and Jitter Wander and jitter present on the output clocks are dependent on: The magnitude of wander and jitter on the selected input reference clock (in Locked mode); The internal wander and jitter transfer characteristic (in Locked mode); The jitter on the local oscillator clock; The wander on the local oscillator clock (in www.semtech.com Frame Sync (8 kHz) and Multi-Frame Sync (2 kHz) clocks will be provided on outputs TO10 (FrSync) and TO11 (MFrSync). The FrSync and MFrSync clocks have a 50:50 mark space ratio. Revision 2.07/Jan 2001 a2001 Semtech Corp 14 ACS8510 SETS ADVANCED COMMUNCIATIONS Holdover mode). Wander and jitter are treated in different ways to reflect their differing impacts on network design. Jitter is always strongly attenuated, whilst wander attenuation can be varied to suit the application and operating state. Wander and jitter attenuation is performed using a digital phase locked loop (DPLL) with a programmable bandwidth. This gives a transfer characteristic of a low pass filter, with a programmable pole. P or t N am e T01 T02 T03 T04 T05 T06 O u t p u t P or t Te c h n o l o g y TTL/CMOS TTL/CMOS TTL/CMOS TTL/CMOS TTL/CMOS PECL/LV DS (LV DS d efault) LV DS/PECL (PECL d efault) A MI TTL/CMOS TTL/CMOS TTL/CMOS FINAL It is sometimes necessary to change the filter dynamics to suit particular circumstances - one example being when locking to a new source, the filter can be opened up to reduce locking time and can then be gradually tightened again to remove wander. Since wander represents a relatively long-term deviation from the nominal operating frequency, it affects the rate of supply of data to the network element. Strong wander attenuation limits the rate of consumption of data to within a smaller range, so a larger buffer Fr e q u e n ci e s S u p p o r t e d 1.544 MHz/2.048 MHz, 3.088 MHz/4.096 MHz, 6.176 MHz/8.192 MHz, 6.48 MHz (d efault), 12.352 MHz/16.384 MHz, 19.44 MHz, 25.92 MHz 1.544 MHz/2.048 MHz, 3.088 MHz/4.096 MHz, 6.176 MHz/8.192 MHz, 12.352 MHz/16.384 MHz, 25.92 MHz, 38.88 MHz (d efault), 51.84 MHz 19.44 MHz - fixed 38.88 MHz - fixed 77.76 MHz - fixed 1.544 MHz/2.048 MHz, 3.088 MHz/4.096 MHz, 6.176 MHz/8.192 MHz, 12.352 MHz/16.384 MHz, 19.44 MHz, 38.88 MHz (d efault), 155.52 MHz, 311.04 MHz 19.44 MHz (d efault), 51.84 MHz, 77.76 MHz, 155.52 MHz 64/8 kHz (comp osite clock, 64 kHz + 8 kHz) 1.544 MHz/2.048 MHz FrSync, 8 kHz - w ith a 50:50 MSR MFrSync, 2 kHz - w ith a 50:50 MSR T07 T08 T09 T010 T011 Table 5: Output Reference Source Selection Table Note for Table 5. Frequencies supported: There are different output clock frequencies available for SONET and SDH applications. SONSDHB controls the default frequency output. F1/F2 means that the output frequency is F1 when the SONSDHB pin is High and F2 when SONSDHB pin is Low. Revision 2.07/Jan 2001 a2001 Semtech Corp 15 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS store is required to prevent data loss. But, since any buffer store potentially increases latency, wander may often only need to be removed at specific points within a network where buffer stores are acceptable, such as at digital cross connects. Otherwise, wander is sometimes not required to be attenuated and can be passed through transparently. The ACS8510 has programmable wander transfer characteristics in a range from 0.1 Hz to 20 Hz. The wander and jitter transfer characteristic is shown in Figure 3. Wander on the local oscillator clock will not have significant effect on the output clock whilst in Locked mode, so long as the DPLL bandwidth is set high enough so that the DPLL can compensate quickly enough for any frequency changes in the crystal. In Free-Running or Holdover mode wander on the crystal is more significant. Variation in crystal temperature or supply voltage both cause drifts in operating frequency, as does ageing. These effects must FINAL be limited by careful selection of a suitable component for the local oscillator, as specified in the section Local Oscillator Clock. Phase Variation There will be a phase shift across the ACS8510 between the selected input reference source and the output clock. This phase shift may vary over time but will be constrained to lie within specified limits. The phase shift is characterised using two parameters, MTIE (Maximum Time Interval Error), and TDEV (Time Deviation), which, although being specified in all relevent specifications, differ in acceptable limits in each one. Typical measurements for the ACS8510 are shown in Figures 4 and 5, for Locked mode operation. Figure 6 shows a typical measurement of Phase Error accumulation in Holdover mode operation. The required performance for phase variation during Holdover is specified in several ways depending upon the particular circumstances 3HDNWRSHDN MLWWHU DQG ZDQGHU DPSOLWXGH ORJ VFDOH -LWWHU FXWRII ORZ IUHTXHQF\ -LWWHU FXWRII KLJK IUHTXHQF\ +] +] 8, # I G% G% -LWWHU DQG ZDQGHU IUHTXHQF\ ORJ VFDOH Figure 3: Wander and Jitter Transfer Characteristsics Revision 2.07/Jan 2001 a2001 Semtech Corp 16 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS pertaining: 1. ETSI 300 462-5, Section 9.1, requires that the shortterm phase error during switchover (i.e., Locked to Holdover to Locked) be limited to an accumulation rate no greater than 0.05 ppm during a 15 second interval. 2. ETSI 300 462-5, Section 9.2, requires that the longterm phase error in the Holdover mode should not exceed {(a1+a2)S+0.5bS2+c}, where a1 = 50 ns/s (allowance for initial frequency offset) a2 = 2000 ns/s (allowance for temperature variation) b = 1.16x10 ns/s (allowance for ageing) -4 2 FINAL Lost_Phase mode is entered. The typical phase disturbance on clock reference source switching will be less than 12 ns on the ACS8510. For clock reference switching caused by the main input failing or being disconnected, then the phase disturbance on the output will still be less than the 120 ns allowed for in the G.813 spec. The actual value is dependant on the frequency being locked to. The PBO requirement, as specified in Telcordia GR1244-CORE, Section 5.7, is that a phase transient of greater than 3.5 s occuring in less than 0.1 seconds should be absorbed. This will be implemented on a future version. ITU-T G.813 states that the max allowable short term phase transient response, resulting from a switch from one clock source to another, with Holdover mode entered in between, should be a maximum of 1 s over a 15 second interval. The maximum phase transient or jump should be less than 120 ns at a rate of change of less than 7.5 ppm and the Holdover performance should be better than 0.05 ppm. On the ACS8510, PBO can be enabled, disabled or frozen using the P interface. By default, it is enabled. When PBO is enabled, it can also be frozen, which will disable the PBO operation on the next input reference switch, but will remain with the current offset. If PBO is disabled while the device is in the Locked mode, there will be a phase jump on the output SEC clocks as the DPLL locks back to 0 degree phase error. Micro-Processor Interface The ACS8510 incorporates a microprocessor interface, which can be configured for the following modes via the bus interface mode control pins UPSEL(2:0) as defined in Table 6. c = 120 ns (allowance for entry into Holdover mode). 3. ANSI Tin1.101-1994, Section 8.2.2, requires that the phase variation be limited so that no more than 255 slips (of 125 s each) occur during the first day of Holdover. This requires a frequency accuracy better than: ((24x60x60)+(255x125s))/(24x60x60) = 0.37 ppm. Temperature variation is not restricted, except to within the normal bounds of 0 to 50 Celsius. 4. Telcordia GR.1244.CORE, Section 5.2. Table 4. shows that an initial frequency offset of 50 ppb is permitted on entering Holdover, whilst a drift over temperature of 280 ppb is allowed; an allowance of 40 ppb is permitted for all other effects. 5. ITU G.822, Section 2.6, requires that the slip rate during category(b) operation (interpreted as being applicable to Holdover mode operation) be limited to less than 30 slips (of 125 s each) per hour ((((60 x 60)/30)+125s)/(60x60)) = 1.042 ppm. Phase Build Out Phase Transient Response and Holdover Phase Build Out (PBO) is the function to minimise phase transients on the output SEC clock during input reference switching. If the currently selected input reference clock source is lost (due to a short interruption, out of frequency detection, or complete loss of reference), the second, next highest priority reference source will be selected. During this transition, the Revision 2.07/Jan 2001 a2001 Semtech Corp 17 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS G .8 13 o ption 1 , co nstan t te m pe rature w a nder lim it FINAL 1 00 Tim e (n s) 10 1 M T IE m e as ure m en t o n 1 55 M H z ou tp ut, 1 9.44 M H z i/p (8 kH z locking), V e ctron 6 6 64 xtal 0.1 0 .01 0.01 0 .1 1 10 1 00 1 00 0 10 00 0 O b serva tio n interva l (s) Figure 4: Maximum Time Interval Error of TOUT0 output port 10 T im e (ns) 1 G .8 13 optio n 1 con s tan t tem perature w ander lim it 0 .1 T D E V m ea su rem e nt on 1 55 M H z ou tpu t, 19.44 M H z i/p (8kH z locking), V ectron 6 664 xtal 0.01 0.01 0.1 1 10 1 00 1 000 100 00 O bs erva tio n interval (s ) Figure 5: Time Deviation of TOUT0 output port 10000000 1000000 Phase Error (ns) P e rm itte d P h a s e E rr o r L im it 100000 10000 T y p ic a l m e a s u r e m e n t, 2 5 C c o n s ta n t te m p e r a tu re 1000 100 1000 10000 100000 O b s e r v a tio n in te rv a l ( s ) Figure 6: Phase error accumulation of TOUT0 output port in hold-over mode Revision 2.07/Jan 2001 a2001 Semtech Corp 18 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS UPSEL(2:0) 111 110 101 100 011 010 001 000 (7) (6) (5) (4) (3) (2) (1) (0) Mode OFF OFF SERIAL MOTOROLA INTEL MULTIPLEXED EPROM OFF Description Interface disabled Interface disabled Serial uP bus interface Motorola interface Intel compatible bus interface Multiplexed bus interface EPROM read mode Interface disabled FINAL right most bit. Some registers carry several individual data fields of various sizes, from single-bit values (e.g. flags) upwards. Several data fields are spread across multiple registers; their organisation is shown in the register map, Table 7. Configuration Registers Table 6: Microprocessor Interface Mode Selection Motorola Mode Parallel data + address: this mode is suitable for use with Motorola's 68x0 type bus. Intel Mode Each configuration register reverts to a default value on power-up or following a reset. Most default values are fixed, but some will be pinsettable. All configuration registers can be read out over the microprocessor port. Status Registers Parallel data + address: this mode is suitable for use with Intel's 80x86 type bus. Multiplexed Mode Data/address: this mode is suitable for use with microprocessors which share bus signals between address and data (e.g., Intel's 80x86 family). Serial Mode The Status Registers contain readable registers. They may all be read from outside the chip but are not writeable from outside the chip (except for a clearing operation). All status registers are read via shadow registers to avoid data hits due to dynamic operation. Each individual status register has a unique location. Register Access This mode is suitable for use with microprocessor which use a serial interface. EPROM Mode This mode is suitable for use with an EPROM, in which configuration data is stored (one-way communication - status information will not be accessible). A state machine internal to the ACS8510 device will perform numerous EPROM read operations to pull the data out of the EPROM. Register Set Most registers are of one of two types, configuration registers or status registers, the exceptions being the Chip_ID and Chip_revision registers. Configuration registers may be written to or read from at any time (the complete 8-bit register must be written, even if only one bit is being modified). All status registers may be read at any time and, in some status registers (such as the sts_interrupts register), any individual data field may be cleared by writing a "1" into each bit of the field (writing a "0" value into a bit will not affect the value of the bit). A description of each register follows. Interrupt Enable and Clear Interrupt requests are flagged on pin INTREQ (active High). Bits in the interrupt status register are set (high) www.semtech.com All registers are 8-bits wide, organised with the most-significant bit positioned in the left-most bit, with bit-significance decreasing towards the Revision 2.07/Jan 2001 a2001 Semtech Corp 19 ACS8510 SETS ADVANCED COMMUNCIATIONS by the following conditions; (i) any reference source becoming valid or going invalid (ii) a change in the operating state (eg. locked, holdover etc.) (iii) brief loss of the currently selected reference source (iv) AMI input error FINAL considered invalid, triggering an interrupt. The time taken to raise this interrupt is dependant on the leaky bucket configuration of the activity monitors. The very fastest leaky bucket setting will still take up to 128 ms to trigger the interrupt. The interrupt caused by the brief loss of the currently selected reference source is provided to facilitate very fast source failure detection if desired. It is triggered after missing just a couple of cycles of the reference source. Some applications require the facility to switch downstream devices based on the status of the reference sources. In order to provide extra flexibility, it is possible to flag the "main reference failed" interrupt (addr 06, bit 6) on the pin TDO. This is simply a copy of the status bit in the interrupt register and is independent of the mask register settings. The bit is reset by writing to the interrupt status register in the normal way. This feature can be enabled and disabled by writing to bit 6 of register 48Hex. All interrupt sources are maskable via the mask register, each one being enabled by writing a '1' to the appropriate bit. Any unmasked bit set in the interrupt status register will cause the interrupt request pin to be asserted (high). All interrupts are cleared by writing a '1' to the bit(s) to be cleared in the status register. When all pending unmasked interrupts are cleared the interrupt pin will go inactive (low). The loss of the currently selected reference source will eventually cause the input to be This section left blank Revision 2.07/Jan 2001 a2001 Semtech Corp 20 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS Register map Shaded areas in the map are dont care and writing either 0 or 1 will not affect any function of the device. Bits labelled Set to 0 or Set to 1 must be set as stated during initialisation of the device, either following power up, or after a power on reset (POR). Failure to correctly set these bits may result in the device operating in an unexpected way. Some registers do not appear in this list. These are either not used, or have test functionality. Do not write to any undefined registers as this may cause the device to operate in a test mode. If an undefined register has been inadvertently addressed, the device should be reset to ensure the undefined registers are at default values. FINAL A d d r. P ar am et er N am e ( Hex ) 7 ( m sb ) 00 01 02 03 04 05 06 08 09 0A 0B 0C 0D 07 0E 0F sts_sources_valid (read only) D at a B i t 6 5 4 3 2 1 0 ( l sb ) Device p ar t numb er (7:0) Device p ar t numb er (15:8) Ch ip revision numb er (7:0) Analog div sync Ph ase loss flag limit Current increment offset (7:0) Current increment offset (15:8) Current increment offset (18:16) Revision 2.07/Jan 2001 a2001 Semtech Corp 21 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS A d d r. P ar am et er N am e ( Hex ) 7 ( m sb ) 10 11 12 13 14 15 16 18 19 1A 1B 1C 1D 1E 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D cnfg_ref_source_frequency (read/w rite) divn divn divn divn divn divn divn divn divn divn divn divn divn divn cnfg_ref_selection_p riority (read/w rite) sts_reference_sources (read/w rite) FINAL D at a B i t 6 5 status 4 3 2 status 1 0 ( l sb ) p rogrammed_p riority p rogrammed_p riority Revision 2.07/Jan 2001 a2001 Semtech Corp 22 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS A d d r. P ar am e t e r N am e ( Hex ) 7 ( m sb ) 30 31 32 33 34 cnfg_sts_remote_sources_ valid (read /w rite) cnfg_op erating_mode (read /w rite) cnfg_ref_selection (read /w rite) cnfg_mode (read /w rite) A u to external 2K enab le Ph ase alarm timeout enab le Hold over Offset enab le Select T0/T1 External 2K Sync enab le FINAL D at a B i t 5 4 3 2 1 0 ( l sb ) 6 Remote status, ch annels <8:1> Remote status, ch annels <14:9> Forced op erating mod e force_select_reference_source SON ET/ SDH I/P Clock ed ge Master/ Slave Reversion mod e 35 36 37 38 cnfg_T4 (read /w rite) cnfg_d ifferential_inp uts (read /w rite) cnfg_uPsel_p ins (read only) cnfg_T0_outp ut_enab le (read /w rite) cnfg_T0_outp ut_freq uencies (read /w rite) cnfg_d ifferential_outp uts (read /w rite) cnfg_b and w id th (read /w rite) cnfg_nominal_freq uency (read /w rite) 311.04MHz on T06 1=SON ET 0=SDH for Dig2 Sq uelch Force T1 inp ut source selection (only valid for inp uts I_5 to I_10) 1=SON ET 0=SDH for Dig1 Digital1 T01 T02 T03 19.44MHz T02 T04 38.88MHz T01 T05 77.76MHz 39 3A 3B Digital2 T07 Freq uency selection A uto b /w sw itch A cq /lock T06 Freq uency selection A cq uisition b and w id th T07 LV DS enab le Set to '0' T07 PECL enab le T06 LV DS enab le T06 PECL enab le N ormal/locked b and w id th 3C 3D 3E 3F 40 N ominal freq uency (7:0) N ominal freq uency (15:8) cnfg_h old over_offset (read /w rite) Hold over offset (7:0) Hold over offset (15:8) A u to Hold over A veraging Hold over offset (18:16) DPLL Freq uency offset limit (7:0) DPLL Freq uency offset limit (9:8) 41 42 43 44 45 46 47 cnfg_freq _limit (read /w rite) cnfg_interrup t_mask (read /w rite) cnfg_freq _d ivn (read /w rite) Divid e-inp ut-b y-n ratio (7:0) Divid e-inp ut-b y-n ratio (13:8) Revision 2.07/Jan 2001 a2001 Semtech Corp 23 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS A d d r. P ar am et er N am e ( Hex ) 7 ( m sb ) 48 cnfg_monitors (read/w rite) FINAL D at a B i t 6 5 Ultra-fast sw itching 4 External source sw itch enab le 3 Freeze p hase b uildout 2 Phase b uildout enab le 1 0 ( l sb ) Flag ref lost on TDO Frequency monitors configuration (1:0) 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F 7F cnfg_activ_up p er_threshold0 (read/w rite) cnfg_activ_low er_threshold0 (read/w rite) cnfg_b ucket_size0 (read/w rite) cnfg_decay_rate0 (read/w rite) cnfg_activ_up p er_threshold1 (read/w rite) cnfg_activ_low er_threshold1 (read/w rite) cnfg_b ucket_size1 (read/w rite) cnfg_decay_rate1 (read/w rite) cnfg_activ_up p er_threshold2 (read/w rite) cnfg_activ_low er_threshold2 (read/w rite) cnfg_b ucket_size2 (read/w rite) cnfg_decay_rate2 (read/w rite) cnfg_activ_up p er_threshold3 (read/w rite) cnfg_activ_low er_threshold3 (read/w rite) cnfg_b ucket_size3 (read/w rite) cnfg_decay_rate3 (read/w rite) cnfg_uPsel (read/w rite) Configuration 0: Activity alarm set threshold (7:0) Configuration 0: Activity alarm reset threshold (7:0) Configuration 0: Activity alarm b ucket size (7:0) Cfg 0:decay_rate (1:0) Configuration 1: Activity alarm set threshold (7:0) Configuration 1: Activity alarm reset threshold (7:0) Configuration 1: Activity alarm b ucket size (7:0) Cfg 1:decay_rate (1:0) Configuration 2: Activity alarm set threshold (7:0) Configuration 2: Activity alarm reset threshold (7:0) Configuration 2: Activity alarm b ucket size (7:0) Cfg 2:decay_rate (1:0) Configuration 3: Activity alarm set threshold (7:0) Configuration 3: Activity alarm reset threshold (7:0) Configuration 3: Activity alarm b ucket size (7:0) Cfg 3:decay_rate (1:0) Micro-p rocessor typ e Revision 2.07/Jan 2001 a2001 Semtech Corp 24 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS Register map description Addr. Parameter N ame (H ex) 00 01 02 chi p_revi si on cnfg_control1 chi p_i d FINAL D escription D efault Value (bin) 00111110 00100001 00000001 Thi s read-only regi ster contai ns the devi ce ID . Address 00 Least-si gni fi cant byte: 3E(hex) Address 01 Most-si gni fi cant byte: 21(hex) 213E(hex) = 8510(dec) Thi s read only regi ster contai ns the chi p revi si on number Bi ts (3:0) & 5 are test controls and should be ei ther set at '0' duri ng i ni ti ali sati on or left unchanged. Bi t 4, when set hi gh, synchroni ses the di vi ders i n the output APLL secti on to the di vi ders i n the D PLL secti on such that thei r phases ali gn. Thi s i s necessary to have the phase ali gnment between the i nputs and output clocks at OC 3 deri ved rates (6.48 MHz to 77.76 MHz). By default, synchroni sati on occurs for 2 seconds after power up and i s then turned off. Setti ng thi s bi t hi gh keeps synchroni sati on on, whi ch may be necessary to avoi d the di vi ders getti ng out of sync when qui ck changes i n frequency occur such as a force i nto freerun mode. 03 X X 000000 cnfg_control2 04 Bi ts (2:0) are test controls and should be set at '010' duri ng i ni ti ali sati on or left unchanged. Bi ts (5:3) defi ne the phase loss flag li mi t. By default set to 4 (100) whi ch corresponds to approxi mately 140. A lower value sets a correspondi ng lower phase li mi t. The flag li mi t determi nes the value at whi ch the D PLL i ndi cates phase lost as a result of i nput ji tter, a phase jump, or a frequency jump on the i nput X X 100010 sts_i nterrupts Thi s 16 bi t regi ster contai ns one bi t for each bi t of sts_sources_vali d, one for loss of reference the devi ce was locked to, and another for the operati ng mode. All bi ts are acti ve hi gh. All bi ts except the mai n_ref_fai led bi t (bi t14) are set on a "change" i n the state of the relevent status bi t, i .e. i f a source becomes vali d, or goes i nvali d i t wi ll tri gger an i nterrupt. If the FSM changes state at all the i nterrupt wi ll be generated. Bi t 14 (mai n_ref_fai led) of the i nterrupt status regi ster i s used to flag i nacti vi ty on the reference that the devi ce i s locked to much more qui ckly than the acti vi ty moni tors can support. If bi t 6 of the cnfg_moni tors regi ster (flag ref loss on TD O) i s set, then the state of thi s bi t i s dri ven onto the TD O pi n of the devi ce. All bi ts are maskable by the bi ts i n the cnfg_i nterrupt_mask regi ster. Each bi t may be cleared i ndi vi dually by wri ti ng a '1' to that bi t, thus resetti ng the i nterrupt. Any number of bi ts can be cleared wi th a si ngle wri te operati on. Wri ti ng '0's wi ll have no effect. 05 06 sts_T4_i nputs Least-si gni fi cant byte (7:0) Most-si gni fi cant byte (15:8) Thi s regi ster holds the status flags of the AMI i nputs and the TOUT4 reference. The alarms once set wi ll hold thei r state unti l reset. Each bi t may be cleared i ndi vi dually by wri ti ng a '1' to that bi t, thus resetti ng the i nterrupt. Wri ti ng '0's wi ll have no effect. These bi ts can also generate i nterrupts. Bit C ontent 0: '1' = Ami 1 Loss of si gnal; '0' = Ami 1 clear 1: '1' = Ami 1 Vi olati on detected; '0' = Ami 1 clear 2: '1' = Ami 2 Loss of si gnal; '0' = Ami 2 clear 3: '1' = Ami 2 Vi olati on detected; '0' = Ami 2 clear 4: '1' = T4 reference fai led - no vali d TIN1 i nput ( 00000000 00000000 08 X X X 10000 sts_operati ng_mode 09 X X X X X 001 Revision 2.07/Jan 2001 a2001 Semtech Corp 25 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS Addr. Parameter N ame (H ex) sts_pri ori ty_table FINAL D escription D efault Value (bin) Thi s i s a 16-bi t read-only regi ster, taki ng two addresses. C urrently-selected reference source: thi s i s the channel number of the i nput reference source whi ch i s currently connected to the SETG functi on. Hi ghest-pri ori ty vali d source: thi s i s the channel number of the i nput reference source whi ch i s vali d and has the hi ghest pri ori ty; i t may not be the same as the currently-selected reference source (due to fai lure hi story or changes i n programmed pri ori ty). Second-hi ghest pri ori ty vali d source: thi s i s the channel number of the i nput reference source whi ch i s vali d and has the next-hi ghest pri ori ty to the hi ghest-pri ori ty vali d source. Thi rd-hi ghest pri ori ty vali d source: thi s i s the channel number of the i nput reference source whi ch i s vali d and has the next-hi ghest pri ori ty to the second-hi ghest-pri ori ty vali d source. Note that these regi sters are updated by the state machi ne i n response to the contents of the cnfg_ref_selecti on_pri ori ty regi ster and the ongoi ng status of i ndi vi dual channels; channel number '0000', appeari ng i n any of these regi sters, i ndi cates that no channel i s avai lable for that pri ori ty. Bit C ontent Hi ghest-pri ori ty vali d source C urrently selected reference source 3rd-hi ghest-pri ori ty vali d source 2nd-hi ghest-pri ori ty vali d source 00000000 00000000 0A 0B sts_curr_i nc_offset (7:4) (3:0) (7:4) (3:0) Thi s read-only regi ster contai ns a si gned-i nteger value representi ng the 19 bi ts of the current i ncrement offset of the di gi tal PLL. The regi ster may be read peri odi cally to bui ld up a hi stori cal database for later use duri ng holdover peri ods (thi s would only be necessary i f an external osci llator whi ch di d not meet the stabi li ty cri teri a descri bed i n Local Osci llator C lock secti on i s used). The regi ster wi ll read 00000000 i mmedi ately after reset. Least si gni fi cant byte of offset value Next si gni fi cant byte of offset value Bi ts (7:4) unused Bi ts (2:0) 3 most si gni fi cant bi ts of offset value 00000000 00000000 X X X X X 000 00000000 X X 000000 0C 0D 07 0E 0F sts_reference_sources sts_sources_vali d Thi s 14 bi t regi ster contai ns copi es of bi t 3 from all the status_reference_sources bytes. Thi s allows the user to get the vali di ty of all sources i n just 2 reads. Thi s regi ster only i ndi cates whether or not a source has passed all cri teri a. Thi s i s a 7-byte regi ster whi ch holds the status of each of the 14 i nput reference sources. The status of each reference source i s shown i n a 4-bi t fi eld. Each bi t i s acti ve hi gh.To ai d status checki ng, a copy of each status bi t 3 i s provi ded i n the sts_sources_vali d regi ster. The status i s reported as follows: (Each bi t may be cleared i ndi vi dually) Status Status Status Status bi t 0 bi t 1 bi t 2 bi t 3 = phase lock alarm = no acti vi ty alarm = out-of-band alarm = Source vali d (no alarms) (bi t 3 i s combi nati on of bi ts (2:0)) The organi sati on of the regi ster i s shown below and i n the regi ster map. Bit 10 11 12 13 14 15 16 (3:0) (7:4) (3:0) (7:4) (3:0) (7:4) (3:0) (7:4) (3:0) (7:4) (3:0) (7:4) (3:0) (7:4) C ontent Status of i nput reference source Revision 2.07/Jan 2001 a2001 Semtech Corp 26 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS Addr. Parameter N ame (H ex) cnfg_ref_selecti on_pri ori ty FINAL D escription D efault Value (bin) Thi s i s a 7-byte regi ster whi ch holds the pri ori ty of each of the 14 i nput reference sources. The pri ori ty values are all relati ve to each other, wi th lower-valued numbers taki ng hi gher pri ori ti es. Only the values 1 to 15 (dec) are vali d - 0 di sables the reference source. Each reference source should be gi ven a uni que number, however two sources gi ven the same pri ori ty number wi ll be assi gned on a fi rst i n fi rst out basi s. It i s sensi ble to reserve the value '1' i n case i t i s necessary to re-order the pri ori ti es on the fly - therefore, the range 2 to 15 would normally be used (i n a slave devi ce, the value 1 i s automati cally used for the protecti on source, i nput #11). All values should be i n hexadeci mal. The organi sati on of the regi ster i s shown below and i n the regi ster map. * The default value gi ven i s vali d when MSTSLVB pi n i s left unconnected or ti ed hi gh. If MSTSLVB i s ti ed low, the default value i s D C (hex). Bit C ontent Programmed pri ori ty of i nput reference source 18 19 1A 1B 1C 1D 1E cnfg_ref_source_frequency (3:0) (7:0) (3:0) (7:4) (3:0) (7:4) (3:0) (7:4) (3:0) (7:4) (3:0) (7:4) (3:0) (7:4) Thi s i s a 14-byte regi ster whi ch holds the keys to the frequenci es of each of the 14 i nput reference sources, as li sted below. Bi ts (3:0) of each byte defi ne the frequency of the reference source i n accordance wi th the followi ng key: 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 8 kHz 1544 kHz (SONET) / 2048 kHz (SD H) (As defi ned by Regi ster 34, bi t 2) 6.48 MHz 19.44 MHz 25.92 MHz 38.88 MHz 51.84 MHz 77.76 MHz 155.52 MHz 2 kHz 4 kHz Bi ts (5:4) of each byte together defi ne whi ch leaky bucket setti ngs (0-3) are used, as defi ned i n regi sters 50 (hex) to 5F (hex). Bi ts (7:6) of each byte defi ne the operati on undertaken on the i nput frequency, i n accordance wi th the followi ng key: 00 01 10 11 The i nput frequency i s fed di rectly i nto the D PLL. The i nput frequency i s i nternally di vi ded down to 8 kHz, before bei ng fed i nto the D PLL. Thi s gi ves excellent ji tter tolerance. Unsupported confi gurati on - do not use. Uses the di vi si on coeffi ci ent stored i n regi ster cnfg_freq_di vn to di vi de the i nput by thi s value pri or to goi ng to the D PLL. The frequency moni tors must be di sabled. The di vi ded down frequency should equal 8kHz. The frequency (3:0) should be set to the nearest spot frequency just below the actual i nput frequency. The D i vN feature works for i nput frequenci es between 1.544 MHz and 100 MHz. * The default value gi ven i s vali d when MSTSLVB pi n i s left unconnected or ti ed hi gh. If MSTSLVB i s ti ed low, the default value i s 03 (hex). 20 21 22 23 Frequency of reference source Revision 2.07/Jan 2001 a2001 Semtech Corp 27 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS Addr. Parameter N ame (H ex) 24 25 26 27 28 29 2A 2B 2C 2D cnfg_sts_remote_sources_ vali d 30 31 cnfg_operati ng_mode 32 Frequency of reference source FINAL D escription D efault Value (bin) 00000011 00000011 00000011 00000011 00000011 00000011 00000010* 00000001 00000001 00000001 Thi s 3-bi t regi ster occupi es the enti re 8-bi t space at address 32(hex). It i s used to force the devi ce i nto a desi red operati ng state, represented by the bi nary values shown i n Fi gure 8. Value 0 (hex) allows the control state machi ne to operate automati cally. Bit (2:0) (7:3) Reference source D esi red operati ng state (as per Fi gure 8) Unused X X X X X 000 cnfg_ref_selecti on Thi s 4-bi t regi ster occupi es the enti re 8-bi t space at address 33(hex). It i s used to force the devi ce to select a parti cular i nput reference source, i rrespecti ve of i ts pri ori ty. Wri ti ng to thi s regi ster temporari ly rai ses the selected i nput to pri ori ty '1'. Provi ded no other i nput i s already programmed wi th pri ori ty '1', and reverti ve mode i s on, thi s source wi ll be selected, i f i t has been vali dated by the frequency and acti vi ty moni tors. Wri ti ng X0(hex) or XF(hex) wi ll di sable all i nput reference sources. * The default i s XF. Bit (3:0) (7:4) Informati on D esi red reference source Unused 33 XXXX1111* cnfg_mode Thi s 7-bi t regi ster occupi es the enti re 8-bi t space at address 34(hex). It contai ns several i ndi vi dual confi gurati on fi elds, as detai led below: Bit 0 = 0 Non-reverti ve Mode: The devi ce wi ll retai n the presently selected source. Thi s i s the default state. = 1 Reverti ve Mode: The devi ce wi ll swi tch to the hi ghest pri ori ty source avai lable shown i n the sts_pri ori ty_table regi ster(7:4) (at address 0A(hex)). Bit 1 = 0 Slave Mode:The devi ce wi ll adopt the slave mode and wi ll follow the master devi ce. = 1 Master Mode:The devi ce wi ll adopt the master mode and make the acti ve deci si ons of whi ch source to select, etc. Thi s bi t i s wri teable, but i ts default value i s determi ned by the pi n, MSTSLVB. 34 11001000 Revision 2.07/Jan 2001 a2001 Semtech Corp 28 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS Addr. Parameter N ame (H ex) cnfg_mode FINAL D escription D efault Value (bin) Bit 2 = 0 SD H Mode:The devi ce expects the i nput frequency of any i nput channel gi ven the value '0001' i n the cnfg_ref_source_frequency regi ster to be 2048 kHz. Thi s bi t i s wri teable, but i ts default value i s determi ned by the pi n, SONSD HB. = 1 SONET Mode:The devi ce expects the i nput frequency of any i nput channel gi ven the value '0001' i n the cnfg_ref_source_frequency regi ster to be 1544 kHz. Thi s bi t i s wri teable, but i ts default value i s determi ned by the pi n, SONSD HB. Bit 3 = 0 External 2 kHz Sync D i sable: The devi ce wi ll i gnore the Sync2k pi n. = 1 External 2 kHz Sync Enable: The devi ce wi ll ali gn the phase of i ts i nternally-generated Frame Sync si gnal (8 kHz) and Multi -Frame Sync si gnal (2 kHz) wi th that of the si gnal suppli ed to the Sync2K pi n. The devi ce should be locked to a 6.48 MHz output from another AC S8510. Thi s i s the default state. Bit 4 = 0 Holdover Offset D i sable: The devi ce wi ll i gnore the value and holdover wi ll use the current PLL i ntegral path value. Thi s i s the default state. = 1 Holdover Offset Enable: The devi ce wi ll adopt the Holdover Offset value stored i n the cnfg_holdover_offset regi ster. Thi s value i s then used to set the frequency i n Holdover mode. Bit 5 = 0 Falli ng C lock Edge Selected: The devi ce wi ll reference to the falli ng edge of the external osci llator si gnal. Thi s i s the default state. = 1 Ri si ng C lock Edge Selected: The devi ce wi ll reference to the ri si ng edge of the external osci llator si gnal. Bit 6 = 0 Phase Alarm Ti meout D i sable: The phase alarm wi ll not ti meout and must be reset externally. = 1 Phase Alarm Ti meout Enable: The phase alarm wi ll ti me out after 100 seconds. Thi s i s the default state. Bit 7 = 0 Auto 2 kHz Sync D i sable:The user controls thi s functi on usi ng bi t 3 of thi s regi ster, as descri bed above. = 1 Auto 2 kHz Sync Enable: External 2 kHz Sync wi ll be enabled only when the source i s locked to 6.48 MHz. Otherwi se i t wi ll be di sabled. Thi s i s the default state. 34 cont 11001000 cnfg_T4 Thi s 6-bi t regi ster occupi es the enti re 8-bi t space at address 35(hex). It contai ns several i ndi vi dual confi gurati on fi elds, as detai led below: Bit (3:0) 4 5 C onfi gurati on fi eld TIN1 i nput source selecti on '1' = Select TOUT0 '0' = Select TIN1 '1' = Squelch '0' = Non-Squelch (D efault) Unused Unused 35 6 7 X X 000000 TIN1 i nput source selecti on: The devi ce wi ll swi tch to the source shown i n thi s fi eld for the generati on of the TOUT4 si gnal. If '0' i t wi ll select the hi ghest pri ori ty acti ve TIN1. Select TOUT0/TIN1: The devi ce wi ll generate the TOUT4 si gnal from the TOUT0 path or the TIN1 path, accordi ng to the status of thi s bi t. Squelch/Non-Squelch: If thi s bi t i s set hi gh the devi ce wi ll squelch the TOUT4 si gnal, causi ng i t to stop toggli ng and remai n at ei ther '1' or '0', If set low i t wi ll not squelch the TOUT4 si gnal. cnfg_di fferenti al_i nputs Thi s 2-bi t regi ster occupi es the enti re 8-bi t space at address 36(hex). It contai ns two i ndi vi dual confi gurati on fi elds, as detai led below: Bit 0 1 (7:2) C onfi gurati on fi eld '1' = Input 36 Revision 2.07/Jan 2001 a2001 Semtech Corp 29 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS Addr. Parameter N ame (H ex) cnfg_uPsel_pi ns FINAL D escription D efault Value (bin) Thi s 3-bi t regi ster occupi es the enti re 8-bi t space at address 37(hex). It holds the key for the selecti on of the mi croprocessor type. It i s read-only, the value bei ng appli ed on the uPSel pi ns and adopted on power-up or reset. After power-up the pi ns are i gnored but can sti ll be read vi a thi s regi ster. Bi t (2:0) 000 001 010 011 100 101 110 111 Mi croprocessor type OFF (i nterface di sabled) EPROM MULTIPLEXED INTEL MOTOROLA SERIAL OFF (i nterface di sabled) OFF (i nterface di sabled) Bi ts(7:3)= XXXXX Bi ts(2:0)= Pi n dependent 37 cnfg_T0_output_enable Thi s 8-bi t regi ster occupi es the enti re 8-bi t space at address 38(hex). It contai ns several i ndi vi dual confi gurati on fi elds, as detai led below: Bit 0 1 2 3 C onfi gurati on fi eld '1' = Output port T05 enabled (77.76 MHz) '0' = Output port T05 di sabled '1' = Output port T04 enabled (38.88 MHz) '0' = Output port T04 di sabled '1' = Output port T03 enabled (19.44 MHz) '0' = Output port T03 di sabled '1' = Output port T02 enabled '0' = Output port T02 di sabled - see regi ster cnfg_T0_output_frequenci es '1' = Output port T01 enabled '0' = Output port T01 di sabled - see regi ster cnfg_T0_output_frequenci es '1' = Sonet mode selected for D i g1 '0' = SD H mode selected for D i g1 - see regi ster cnfg_T0_output_frequenci es '1' = Sonet mode selected for D i g2 '0' = SD H mode selected for D i g2 - see regi ster cnfg_T0_output_frequenci es '1' = T06 output frequency set to 311.04 MHz '0' = T06 output frequency set by Address 3A (5:4) 00011111 38 4 5 6 7 Note: "D i sabled" means that the output port holds a stati c logi c value (the port i s not Tri stated). cnfg_T0_output_frequenci es Thi s regi ster holds the frequency selecti ons for each output port, as detai led below. Bit (1:0) 00 01 10 11 39 (5:4) 00 01 10 11 * = default C onfi gurati on fi eld T01 6.48 MHz* 25.92 MHz 19.44 MHz D i g1 D i g1 1544 kHz/2048 kHz* 3088 kHz/4096 kHz 6176 kHz/8192 kHz 12352 kHz/16384 kHz Bit (3:2) 00 01 10 11 (7:6) 00 01 10 11 C onfi gurati on fi eld T02 25.92 MHz 51.84 MHz 38.88 MHz* D i g2 D i g2 1544 kHz/2048 kHz* 3088 kHz/4096 kHz 6176 kHz/8192 kHz 12352 kHz/16384 kHz 00001000 - For both D i g1 and D i g2, the left most frequency values are for Sonet mode and the others are for SD H mode. They are selected vi a the SONET/SD H bi ts i n regi ster cnfg_T0_output_enable. Revision 2.07/Jan 2001 a2001 Semtech Corp 30 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS Addr. P arameter N ame (H ex) cnfg_di fferenti al_outputs FINAL D escription D efault Value (bin) Thi s regi ster holds the frequency selecti ons and the port-technology type for the di fferenti al outputs, T06 and T07, as detai led below. Bit (1:0) 00 01 10 11 (5:4) 00 01 10 11 * = default C onfi gurati on fi eld T06 P ort di sabled P E C L-compati ble LV D S -compati ble* unused T06 38.88 MHz* 19.44 MHz 155.52 MHz D i g1. Bit (3:2) 00 01 10 11 (7:6) 00 01 10 11 C onfi gurati on fi eld T07 P ort di sabled P E C L-compati ble* LV D S -compati ble unused T07 155.52 MHz 51.84 MHz 77.76 MHz 19.44 MHz* 3A 11000110 cnfg_bandwi dth Thi s regi ster contai ns i nformati on used to control the operati on of the di gi tal P LL. When bandwi dth selecti on i s set to automati c, the D P LL wi ll use the acqui si ti on bandwi dth setti ng when out of lock, and the normal/locked bandwi dth setti ng when i n lock. When set to manual, the D P LL wi ll alway use the normal/locked bandwi dth setti ng. B i t (2:0) 000 001 010 011 100 101 110 111 3 Loop bandwi dth 0.1 Hz 0.3 Hz 0.6 Hz 1.2 Hz 2.5 Hz 5.0 Hz 10 Hz 20 Hz unused (6:4) 000 001 010 011 100 101 110 111 7 A cqui si ti on bandwi dth 0.1 Hz 0.3 Hz 0.6 Hz 1.2 Hz 2.5 Hz 5.0 Hz 10 Hz 20 Hz B andwi dth selecti on '0'= Manual operati on '1'= A utomati c operati on 3B 0111X 101 cnfg_nomi nal_frequency Thi s regi ster holds a 16 bi t unsi gned i nteger representi ng the desi red nomi nal frequency. Thi s i s avai lable to opti onally cali brate the nomi nal output frequency to compensate agai nst vari ati on i n the external crystal frequenci es. Least-si gni fi cant byte. 10011001 3C 3D cnfg_holdover_offset Most-si gni fi cant byte. 10011001 Thi s 16-bi t regi ster uses addresses 3E (hex) to 40(hex). It holds a 16 bi t si gned i nteger, representi ng the holdover offset value, whi ch can be used to set the holdover mode frequency when enabled vi a the holdover offset enabled bi t i n the cnfg_mode regi ster. B i t (7:0) Holdover offset (7:0) 00000000 3E 3F B i t (7:0) Holdover offset (15:8) 00000000 40 B i t (2:0) Holdover offset (18:16) B i t 7 i s A uto Holdover A veragi ng enable - default 1. Thi s enables the frequency average to be taken from 32 samples. One sample taken every 32 seconds, after the frequency has been confi rmed to be i n-band by the frequency moni tors, gi vi ng a 17 mi nute hi story of the currently locked to reference source for use i n Holdover. B i t (6:3) Unused cnfg_freq_li mi t Thi s regi ster holds a 10 bi t unsi gned i nteger representi ng the pull-i n range of the D P LL. It should be set accordi ng to the accuracy of crystal i mplemented i n the appli cati on, usi ng the followi ng formula: Frequency range +/- (ppm) = (cnfg_freq_li mi t x 0.0785)+0.01647 or cnfg_freq_li mi t = (Frequency range - 0.01647) / 0.0785 D efault value when S RC S W i s left unconnected or ti ed low i s 9.2 ppm. D efault value when S RC S W i s hi gh i sthe full range of around 80 ppm. 1X X X X 000 41 Least si gni fi cant byte 01110110 (S RC S W low) 11111111 (S RC S W hi gh) X X X X X X 00 (S RC S W low) X X X X X X 11 (S RC S W hi gh) 42 (7:2) Unused (1:0) Most si gni fi cant byte Revision 2.07/Jan 2001 a2001 Semtech Corp 31 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS Addr. Parameter N ame (H ex) 43 44 45 cnfg_freq_di vn Thi s 14 bi t i nteger i s used as the di vi sor for any i nput appli ed to FINAL D escription D efault Value (bin) 11111111 11111111 XXX11111 Each bi t of thi s 21 bi t regi ster, i f set to zero, wi ll di sable the appropri ate i nterrupt source i n ei ther the i nterrupt status regi ster or the sts_T4_i nputs regi ster. X X X X X X 01 54 55 56 57 cnfg_acti v_upper_threshold1 Thi s 8 bi t regi ster sets the value i n the leaky bucket that causes the acti vi ty alarm to be rai sed. cnfg_acti v_lower_threshold1 Thi s 8 bi t regi ster sets the value i n the leaky bucket that causes the acti vi ty alarm to be cleared. cnfg_bucket_si ze1 cnfg_decay_rate1 Thi s 8 bi t regi ster sets the maxi mum value that the leaky bucket can reach gi ven an i nacti ve i nput. As for regi ster 53(hex) but for bucket 1. 00000110 00000100 00001000 X X X X X X 01 Revision 2.07/Jan 2001 a2001 Semtech Corp 32 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS Addr. Parameter N ame (H ex) 58 59 5A 5B 5C 5D 5E 5F cnfg_acti v_lower_threshold2 cnfg_bucket_si ze2 cnfg_decay_rate2 FINAL D escription D efault Value (bin) 00000110 00000100 00001000 X X X X X X 01 00000110 00000100 00001000 X X X X X X 01 Bi ts(7:3)= XXXXX Bi ts(2:0)= Pi n dependent cnfg_acti v_upper_threshold2 Thi s 8 bi t regi ster sets the value i n the leaky bucket that causes the acti vi ty alarm to be rai sed. Thi s 8 bi t regi ster sets the value i n the leaky bucket that causes the acti vi ty alarm to be cleared. Thi s 8 bi t regi ster sets the maxi mum value that the leaky bucket can reach gi ven an i nacti ve i nput. As for regi ster 53(hex) but for bucket 2. cnfg_acti v_upper_threshold3 Thi s 8 bi t regi ster sets the value i n the leaky bucket that causes the acti vi ty alarm to be rai sed. cnfg_acti v_lower_threshold3 cnfg_bucket_si ze3 cnfg_decay_rate3 cnfg_uPsel Thi s 8 bi t regi ster sets the value i n the leaky bucket that causes the acti vi ty alarm to be cleared. Thi s 8 bi t regi ster sets the maxi mum value that the leaky bucket can reach gi ven an i nacti ve i nput. As for regi ster 53(hex) but for bucket 3. Thi s 3 bi t regi ster i s used to control the mode of the mi croprocessor i nterface. Thi s wi ll power-up wi th the value on the Psel pi ns. Subsequently, the regi ster can be wri tten to put the mi cro-processor i nterface i nto another mode. Thi s wi ll support booti ng from EPROM and subsequently communi cati ng vi a another mode. The value on the pi ns can always be read vi a the cnfg_uPsel_pi ns regi ster. These 3 pi ns can be used as general purpose i nputs for the P i f necessary after booti ng. 7F Selection Source of Input Reference Clock Under normal operation, the input reference sources are selected automatically by an order of priority. But, for special circumstances, such as chip or board testing, the selection may be forced by configuration. Automatic operation selects a reference source based on its pre-defined priority and its current availability. A table is maintained which lists all reference sources in the order of priority. This is initially downloaded into the ACS8510 via the micro-processor interface by the Network Manager, and is subsequently modified by the results of the ongoing quality monitoring. In this way, when all the defined sources are active and valid, the source with the highest programmed priority is selected but, if this source fails, the next-highest source is selected, and so on. Restoration of repaired reference sources is handled carefully to avoid inadvertent disturbance of the output clock. The ACS8510 has two modes of operation; Revertive and Non-Revertive. In Revertive mode, if a reRevision 2.07/Jan 2001 a2001 Semtech Corp 33 validated (or newly validated) source has a higher priority than the reference source which is currently selected, a switch over will take place. Many applications prefer to minimise the clock switching events and choose NonRevertive mode. In Non-Revertive mode , when a re-validated (or newly validated) source has a higher priority then the selected source will be maintained. The re-validation of the reference source will be flagged in the sts_sources_valid register and, if not masked, will generate an interrupt. Selection of the re-validated source can only take place under software control the software should briefly enable Revertive mode to affect a switch-over to the higher priority source. If the selected source fails under these conditions the device will still not select the higher priority source until instructed to do so by the software, by briefly setting the Revertive mode bit. When there is a reference available with higher priority than the selected reference, there will be NO change of reference source as long as the Non-Revertive mode remains on. This is the case even of there are lower priority references available or the currently selected reference fails. When the ONLY valid reference sources that are available www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS have a lower priority than the selected reference, a failure of the selected reference will always trigger a switch-over regardless of whether Revertive or Non-revertive mode has been chosen. Also, in a Master/Slave redundancy-protection scheme, the Slave device(s) must follow the Master device. The alignment of the Master and Slave devices is part of the protection mechanism. The availability of each source is determined by a combination of local and remote monitoring of each source. Each input reference source supplied to each ACS8510 device is monitored locally and the results are made available to other devices. Forced Control Selection FINAL selection priority values are all relative to each other, with lower-valued numbers taking higher priorities. Each reference source should be given a unique number, the valid values are 1 to 15 (dec). A value of 0 disables the reference source. However if two or more inputs are given the same priority number those inputs will be selected on a first in, first out basis. If the first of two same priority number sources goes invalid the second will be switched in. If the first then becomes valid again, it becomes the second source on the first in, first out basis, and there will not be a switch. If a third source with the same priority number as the other two becomes valid, it joins the priority list on the same first in, first out basis. There is no implied priority based on the channel numbers. The input port - Activity (toggling) - Frequency (This monitoring is only performed when there is no irregular operation of the clock or loss of clock condition) A configuration register, 'cnfg_ref_selection', controls both the choice of automatic or forced selection and the selection itself (when forced selection is required). The forced selection of an input reference source occurs when the 'cnfg_ref_selection' variable contains a non-zero value, the value then representing the input port required to be selected. This is not the normal mode of operation, and the 'cnfg_ref_selection' variable is defaulted to the all-zero value on reset, thereby adopting the automatic selection of the reference source. Automatic Control Selection When an automatic selection is required, the 'cnfg_ref_selection' register must be set to allzero. The configuration registers, 'cnfg_ref_selection_priority', held in the P port block, consists of seven, 8 bit registers organised as one 4 bit register per input reference port. Each register holds a 4-bit value which represents the desired priority of that particular port. Unused ports should be given the value, '0000' or '1111', in the relevant register to indicate they are not to be included in the priority table. On power-up, or following a reset, the whole of the configuration file will be defaulted to the values defined by Table 1. The Revision 2.07/Jan 2001 a2001 Semtech Corp 34 In addition, input ports ACS8510 SETS ADVANCED COMMUNCIATIONS signal, loss-of-activity, loss-of-regularity or clockout-of-band condition will be declared as unavailable. Clock quality monitoring is a continuous process which is used to identify clock problems. There is a difference in dynamics between the selected clock and the other reference clocks. Anomalies occurring on non-selected reference sources affect only that source's suitability for selection, whereas anomalies occurring on the selected clock could have a detrimental impact on the accuracy of the output clock. Anomalies, whether affecting signal-purity or signal frequency, could induce jitter or frequency offsets in the output clock, leading to anomalous behaviour. Anomalies on the selected clock, therefore, have to be detected as they occur and the phase locked loop must be temporarily isolated until the clock is once again pure. The clock monitoring process cannot be used for this because the high degree of accuracy required dictates that the process be slow. To achieve the immediacy required by the phase locked loop requires an alternative mechanism. The phase locked loop itself contains appropriate circuitry, based around the FINAL phase detector, and isolates itself from the selected reference source as soon as a signal impurity is detected. It can likewise respond to frequency offsets outside the permitted range since these result in saturation of the phase detector. When the phase locked loop is isolated from the reference source, it is essentially operating in a Hold-Over state; this is preferable to feeding the loop with a standby source, either temporarily or permanently, since excessive phase excursions on the output clock are avoided. Anomalies detected by the phase detector are integrated in a leaky bucket accumulator. Occasional anomalies do not cause the accumulator to cross the alarm-setting threshold, so the selected reference source is retained. Persistent anomalies cause the alarmsetting threshold to be crossed and result in the selected reference source being rejected. Activity Monitoring The ACS8510 has a combined inactivity and irregularity monitor. The ACS8510 uses a "leaky bucket" accumulator, which is a digital circuit which mimics the operation of an analog integrator, in which input pulses increase the inactivities/irregularities reference source bucket_size leaky bucket response programmable fall slopes upper_threshold lower_threshold (all programmable) alarm Figure 7: Inactivity and irregularity monitoring Revision 2.07/Jan 2001 a2001 Semtech Corp 35 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS output amplitude but die away over time. Such integrators are used when alarms have to be triggered either by fairly regular defect events, which occur sufficiently close together, or by defect events which occur in bursts. Events which are sufficiently spread out should not trigger the alarm. By adjusting the alarm-setting threshold, the point at which the alarm is triggered can be controlled. The point at which the alarm is cleared depends upon the decay rate and the alarm-clearing threshold. On the alarm-setting side, if several events occur close together, each event adds to the amplitude and the alarm will be triggered quickly; if events occur a little more spread out, but still sufficiently close together to overcome the decay, the alarm will be triggered eventually. If events occur at a rate which is not sufficient to overcome the decay, the alarm will not be triggered. On the alarm-clearing side, if no defect events occur for a sufficient time, the amplitude will decay gradually and the alarm will be cleared when the amplitude falls below the alarm- FINAL clearing threshold. The ability to decay the amplitude over time allows the importance of defect events to be reduced as time passes by. This means that, in the case of isolated events, the alarm will not be set, whereas, once the alarm becomes set, it will be held on until normal operation has persisted for a suitable time (but if the operation is still erratic, the alarm will remain set). See Figure 7. The "leaky bucket" accumulators are programmable for size, alarm set & reset thresholds and decay rate. Each source is monitored over a 128 ms period. If, within a 128 ms period, an irregularity occurs that is not deemed to be due to allowable jitter/wander, then the accumulator is incremented. The accumulator will continue to increment up to the point that it reaches the programmed bucket size. The "fill rate" of the leaky bucket is, therefore, 8 units/second. The "leak rate" of the leaky bucket is programmable to be in multiples of the fill rate (x1, x0.5, x0.25 and x0.125) to give a programmable leak rate from Leaky bucket timing The time taken to raise an inactivity alarm on a reference source that has previously been fully active (leaky bucket empty) will be: (cnfg_activ_upper_threshold N) 8 where N is the number of the relevent leaky bucket configuration. If an input is intermittently inactive then this time can be longer. The default setting of cnfg_activ_upper_threshold is 6, therefore the default time is 0.75 s. The time taken to cancel the activity alarm on a previously completely inactive reference source is calculated as: (cnfg_decay_rate N) 2 x ((cnfg_bucket_size N) - (cnfg_activ_lower_thrshold N)) secs 8 where N is the number of the relevent leaky bucket configuration in each case. The default setting are shown in the following: 1 2 x (8-4) = 1.0 s 8 secs Revision 2.07/Jan 2001 a2001 Semtech Corp 36 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS 8 units/sec down to 1 unit/sec. A conflict between trying to leak at the same time as a fill is avoided by preventing a leak when a fill event occurs. Disqualification of a non-selected reference source is based on inactivity, or on an out of band result from the frequency monitors. The currently selected reference source can be disqualified for phase, frequency, inactivity or if the source is outside the DPLL lock range. If the currently selected reference source is disqualified, the next highest priority, active reference source is selected. Ultra Fast Switching FINAL enabled on power-up and the feature has since been enabled. When the TDO output from the ACS8510 is connected to the TDI pin of the next device in the JTAG scan chain, the implementation should be such that a logic change caused by the action of the interrupt on the TDI input should not effect the operation when JTAG is not active. External Protection Switching A reference source is normally disqualified after the leaky bucket monitor thresholds have been crossed. An option for a faster disqualification has been implemented, whereby if register 48H, bit 5 (Ultra Fast Switching), is set then a loss of activity of just a few reference clock cycles will set the no activity alarm and cause a reference switch. This can be chosen to cause an interrupt to occur instead of or as well as causing the reference switch. The sts_interrupts register 05 Hex Bit 15 (main_ref_failed) of the interrupt status register is used to flag inactivity on the reference that the device is locked to much faster than the activity monitors can support. If bit 6 of the cnfg_monitors register (flag ref loss on TDO) is set, then the state of this bit is driven onto the TDO pin of the device. The flagging of the loss of the main reference failure on TDO is simply allowing the status of the sts_interrupt bit 15 to be reflected in the state of the TDO output pin. The pin will, therefore remain High until the interrupt is cleared. This functionality is not enabled by default so the usual JTAG functions can be used. When JTAG is normally used straight out of power-up, then this feature will have no bearing on the functionality. The TDO flagging feature will need to be disabled if JTAG is not Revision 2.07/Jan 2001 a2001 Semtech Corp 37 Fast external switching between inputs Frequency Monitoring The ACS8510 performs frequency monitoring to identify reference sources which have drifted outside the acceptable frequency range of +/16.6 ppm (measured with respect to the output clock). The sts_reference sources out-of-band alarm for a particular reference source is raised when the reference source is outside the acceptable frequency range. The ACS8510 DPLL has a programmable frequency limit of +/- 80 ppm. If the range is programmed to be > 16.6 ppm, the activity monitors should be www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS disabled so the input reference source is not automatically rejected as out of frequency range. Modes of Operation The ACS8510 has three primary modes of operation (Free-Run, Locked and Holdover) supported by three secondary, temporary modes (Pre-Locked, Lost_Phase and PreLocked2). These are shown in the State Transition Diagram, Figure 8. The ACS8510 can operate in Forced or Automatic control. On reset, the ACS8510 reverts to Automatic Control, where transitions between states are controlled completely automatically. Forced Control can be invoked by configuration, allowing transitions to be performed under external control. This is not the normal mode of operation, but is provided for special occasions such as testing, or where a high degree of hands-on control is required. Free-Run mode FINAL device cannot achieve lock within 100 seconds, it reverts to Free-Run mode and another reference source is selected. Locked mode The Free-Run mode is typically used following a power-on-reset or a device reset before network synchronisation has been achieved. In the Free-Run mode, the timing and synchronisation signals generated from the ACS8510 are based on the Master clock frequency provided from the external oscillator and are not synchronised to an input reference source. The frequency of the output clock is a fixed multiple of the frequency of the external oscillator, and the accuracy of the output clock is equal to the accuracy of the Master clock. The transition from Free-Run to Pre-locked(1) occurs when the ACS8510 selects a reference source. Pre-Locked(1) mode The Locked mode is used when an input reference source has been selected and the PLL has had time to lock. When the Locked mode is achieved, the output signal is in phase and locked to the selected input reference source. The selected input reference source is determined by the priority table. When the ACS8510 is in Locked mode, the output frequency and phase follows that of the selected input reference source. Variations of the external crystal frequency have a minimal effect on the output frequency. Only the minimum to maximum frequency range is affected. Note that the term, 'in phase', is not applied in the conventional sense when the ACS8510 is used as a frequency translator (e.g., when the input frequency is 2.048 MHz and the output frequency is 19.44 MHz) as the input and output cycles will be constantly moving past each other; however, this variation will itself be cyclical over time unless the input and output are not locked. Lost_Phase mode Lost_Phase mode is used whenever the selected reference source suffers most kinds of anomalous behaviour. Clock generation is performed in the same way as in the Holdover mode. If the leaky bucket accumulator calculates that the anomaly is serious, the device rejects the reference source and one of the following transitions takes place: Go to Pre-Locked(2); - If a known-good standby source is available. Go to Hold-Over; - If no standby sources are available. The ACS8510 will enter the Locked state in a maximum of 100 seconds, as defined by GR1244-CORE specification, if the selected reference source is of good quality. If the Revision 2.07/Jan 2001 a2001 Semtech Corp 38 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS Holdover mode FINAL important - the stability of the output clock in Hold-Over is directly related to the stability of the external oscillator. Pre-Locked(2) mode The Holdover mode is used when the ACS8510 was in Locked mode for long enough to acquire stable frequency data, but the final selected reference source has become unavailable and a replacement has not yet been qualified for selection. In Holdover mode, the ACS8510 provides the timing and synchronisation signals to maintain the Network Element (NE), but they are not phase locked to any input reference source. The timing is based on a stored value of the frequency ratio obtained during the last Locked mode period. The Holdover performance is mainly limited by what is happening to the TCXO. The ACS8510 has 3 ways of determining Holdover, either; 1. By external frequency setting (cnfg_holdover_offset register) 2. By an internal frequency measuring and averaging system which averages the last 20 minutes 3. By just using the last frequency (as reported by the sts_curr_inc_offset register). This value can be read out of the device and used to build up a longer term average using an external averaging circuit. This value can then to readback into the device and used as the Holdover offset (via cnfg_holdover_offset register). This state is very similar to the Pre-Locked(1) state. It is entered from the Holdover state when a reference source has been selected and applied to the phase locked loop. It is also entered if the device is operating in revertive mode and a higher-priority reference source is restored. Upon applying a reference source to the phase locked loop, the ACS8510 will enter the Locked state in a maximum of 100 seconds, as defined by GR-1244-CORE specification, if the selected reference source is of good quality. If the device cannot achieve lock within 100 seconds, it reverts to Holdover mode and another reference source is selected. Protection Facility The ACS8510 supports redundancy protection. The primary functions of this include: - Alignment of the priority tables of both Master and Slave ACS8510 devices so as to align the selection of reference sources of both Master and Slave ACS8510 devices. - Alignment of the phases of the 8 kHz and 2 kHz clocks in both Master and Slave ACS8510 devices to within one cycle of the 77.76 MHz internal clock. When two ACS8510 devices are to be used in a redundancy-protection scheme within an NE, one will be designated as the Master and the other as the Slave. It is expected that an NE will use the T OUT0 output for its internal operations because the TOUT4 output is intended to feed an SSU/BITS system. An SSU/BITS will not be bothered by phase differences between www.semtech.com By default it uses the internal averager. This means that if the TCXO frequency is varying due to temperature fluctuations in the room, then the instantaneous value can be different from the average value, and then it may be possible to exceed the 0.05 ppm limit (depending on how extreme the temperature flucuations are). It is advantageous to shield the TCXO to slow down frequency changes due to drift and external temperature fluctuations. The frequency accuracy of Holdover mode has to meet the ITU-T, ETSI and Telcordia performance requirements. The performance of the external oscillator clock is critical in this mode, although only the frequency stability is Revision 2.07/Jan 2001 a2001 Semtech Corp 39 ACS8510 SETS ADVANCED COMMUNCIATIONS signals arriving from different sources because it typically incorporates line build-out functions to absorb phase differences on reference inputs. This means that the phasing of the composite clocks between two ACS8510 devices do not have to be mutually-aligned. The same is not true, however, of the TOUT0 output signals (T01 - T07, Frame clock and Multi-Frame clock). It is usually important to align the phases of all equivalent T OUT0 signals generated by different sources so that switch-over from one device to another does not affect the internal operations of the NE. Both ACS8510 devices will produce the same signals, which will be routed around the NE to the various consumers (clock sinks). With the possible exception of a through-timing mode, the signals from the Master device will be used by all consumers, unless the Master device fails, when each consumer will switch over to the signals generated by the Slave device. Switchover to a new TOUT0 clock should be as hitless as possible. This requires the signals of both ACS8510 devices to be phase aligned at each consumer. Phase alignment requires frequency alignment. To ensure that both devices can generate output clocks locked to the same source, both devices are supplied with the same reference sources on the same input ports and will have identical priority tables. Failures of selected reference sources will result in both ACS8510 devices making the same updates to their priority tables as availability information will be updated in both devices. Although, in principle, the priority tables will be the same if the same reference sources are used on the same input port on each device, in practice, this is only true if the reference sources actually arrive at each device - failures of a source seen only by one device and not by the other, such as could be caused, for example, by a backplane connector failure, would result in the priority tables becoming misaligned. It is thus necessary to force the priority tables to Revision 2.07/Jan 2001 a2001 Semtech Corp 40 FINAL be aligned under normal operating conditions so that the devices can make the same decisions - this can be achieved by loading the availability seen by one device (via the sts_reference_sources register) into the cnfg_sts_remote_sources_valid register of the other device. Another factor which could affect hit-less switching is the frequency of the local oscillator clock used by each ACS8510 device: these clocks are not mutually aligned and, whilst this has no impact on the frequency of the output clocks during locked mode, it could cause the output frequencies to diverge during Holdover mode if no action were taken to avoid it. In order to maintain alignment of the output frequencies of each ACS8510 device even during Holdover, the Master device's 6.48 MHz output is fed into the Slave device on its www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS has to be repaired and replaced. When this occurs, the new Master cannot immediately adopt its normal role because it must not cause phase hits on the output clocks. It has, therefore, to adopt a subordinate role to the active Slave device, at least until such time as it has acquired alignment to the 8 kHz and 2 kHz frame and Multi-Frame clocks and the priority table of the Slave device; then, when a switch-back (restoration) is ordered, the Master can take over responsibility. These activities, in Master or Slave operation, are detailed in Table 8. Alignment of priority tables in Master and Slave ACS8510 FINAL The monitoring of the reference sources performed by a Master ACS8510 results in a list of available sources being placed in a sts_valid_sources register. This information is used within the device as one of the masks used to build the device's priority table. The information is passed to the Slave device and used to configure the cnfg_sts_remote_sources_valid register so that it can use it as a mask in building its own priority tables. The information is passed between devices using the microprocessor port. Alignment of the selection of reference sources for T OUT4 generation in the Master and Slave ACS8510 Correct protection will only be achieved by connecting individual reference sources to the same input ports on each device and priority tables in each device must be aligned to each other. The Master device must take account of the availability of each reference source seen by another device and a Slave device must adopt the same order of priority as the Master device (except that the slave's highest-priority input is Revision 2.07/Jan 2001 a2001 Semtech Corp 41 As stated previously, there is no need to align the phases of the TOUT4 outputs in Master and Slave devices. There is a need, however, to ensure that all devices select the same reference source. But, since there is no Holdover mode required for the generation of the TOUT4 clock, and every reference source is continuously monitored within each device, it is permissible to rely on external intelligence to command a switch-over to an alternative source should the selected one fail. The time delay involved in detecting the failure, indicating it to the outside and selecting a new source, will result only in the SSU/BITS entering its HoldOver mode for a short time. Alignment of the phases of the 8kHz and 2kHz clocks in both Master and Slave ACS8510 In addition to aligning the edges of the TOUT0 outputs of Master and Slave devices, it is necessary to align the edges of the Frame and Multi-Frame clocks. If this is not performed, frame alignment may be lost in distant equipment on switch-over to an alternative device, resulting in anomalous network operation of a very serious nature. In accordance with the alignment mechanism used with the main TOUT0 clock (described in the www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS opening paragraphs of this section), whereby the 6.48 MHz output of the Master device is supplied to the Slave device, the alignment of both the 8 kHz and 2 kHz clocks is accomplished (they are already synchronous to the TOUT0 clocks) by feeding the 2 kHz clock of the Master device into the Slave device. The Multi-Frame Sync clock output of the Slave device is also fed to the Sync2K input of the Master device. Alignment of the Multi-Frame Sync input occurs only when cnfg_mode register, bit 3, address 34Hex External 2 kHz Sync Enable is set to 1. JTAG The JTAG connections on the ACS8510 allow a full boundary scan to be made. The JTAG implementation is fully compliant to IEEE 1149.1, with the following minor exceptions, and the user should refer to the standard for further information. 1. The output boundary scan cells do not capture data from the core, and so do not support EXTEST. However this does not affect board testing. FINAL 2. In common with some other manufacturers, pin TRST is internally pulled low to disable JTAG by default. The standard is to pull high. The polarity of TRST is as the standard: TRST high to enable JTAG boundary scan mode, TRST low for normal operation. 3. The device does not support the optional tri-state capability (HIGHZ). This will be supported on the next revision of the device. The JTAG timing diagram is shown on page 53. PORB The Power On Reset (PORB) pin resets the device if forced Low for a power-on-reset to be initiated. The reset is asynchronous, the minimum Low pulse width is 5 ns. Reset is needed to initialize all of the register values to their defaults. Asserting Reset (POR) is required at power on, and may be re-asserted at any time to restore defaults. This is implemented most simplistically by an external capacitor to GND along with the internal pull-up resistor. The ACS8510 is held in a reset state for 250 ms after the PORB pin has been pulled High. In normal operation PORB should be held High. Notes to Table 8 Note 1: Both ACS8510 must build a common priority table so that the Slave ACS8510 can select the same input reference source as the Master ACS8510 if the Master fails (when the Master is OK, the Slave locks to the Master's output). Note 2: Slave ACS8510 uses common priority table, built before Master ACS8510 failed - priority table can be modified as status of the input reference sources changes Note 3: Slave ACS8510 outputs must remain in phase with those of Master ACS8510 Revision 2.07/Jan 2001 a2001 Semtech Corp 42 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS TCXO FINAL VDD MASTER 6.48 MHz MSTSLVB SEC1 SEC2 SEC3 I_1 I_2 I_3 . . . I_11 . . . I_14 SYNC2K T 01 T 02 T 03 T 04 . . . T 07 . . . T 011 MFr Sync SEC14 6.48 MHz TCXO SLAVE MSTSLVB GND SEC1 SEC2 SEC3 I_1 I_2 I_3 . . . I_11 . . . I_14 SYNC2K SYNC2K_EN=1 34Bit3 T01 T 02 T 03 T 04 . . . T 07 . . . T011 MFr Sync SEC13 R e f _ so u r ce s t o M ast e r A C S 8510 A ll good Some failed Good Good Good Failed Failed Failed Failed R e f _ so u r ce s t o S l av e A C S 8510 A ll good Some oth ers failed Good Good Good Failed Failed Failed Failed M ast e r A C S 8510 s t at u s Good Good Good Failed Failed Failed Good Failed Failed S l av e A C S 8510 s t at u s Good Good Failed Good Failed Good Failed Good Failed M ast e r A C S 8510 Locked (ref_x) Locked (ref_y) Locked (ref_x) Dead Dead Hold over Hold over Dead Dead S l av e A C S 8510 ou t p u t Locked to master Locked to master Dead Locked (ref_x) Dead Locked to master Dead Hold over Dead Com m en t s N ote 1 N ote 1 N ote 2 N ote 3 N ote 4 Table 8: Master-Slave ACS8510 Relationship Revision 2.07/Jan 2001 a2001 Semtech Corp 43 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS FINAL (1)Reset free-run select ref (state 001) (3) no valid standby ref & (main ref invalid or out of lock >100s) (2) all refs evaluated & at least one ref valid Reference sources are flagged as 'valid' when active, 'in-band' and have no phase alarm set. (4) valid standby ref & [ main ref invalid or (higher-priority ref valid & in revertive mode) or out of lock >100s] pre-locked w ait for up to 100s (state 110) All sources are continuously checked for activity and frequency. Only the main source is checked for phase. A phase lock alarm is only raised on a reference when that reference has lost phase whilst being used as the main reference. The micro-processor can reset the phase lock alarm. A source is considered to have phase locked when it has b een continuously in phase lock for between 1 and 2 seconds (5) selected ref phase locked locked keep ref (state 100) (10) selected source phase locked (9) valid standby ref & [ main ref invalid or (higher-priority ref valid & in revertive mode) ] (6) no valid standby ref & main ref invalid (8) phase regained within 100s (7) phase lost on main ref pre-locked2 w ait for up to 100s (state 101) (12) valid standby ref & (main ref invalid or out of lock >100s) Lost phase w ait for up to 100s (state 111) (11) no valid standby ref & (main ref invalid or out of lock >100s) holdover select ref (state 010) (15) valid standby ref & [ main ref invalid or (higher-priority ref valid & in revertive mode) or out of lock >100s] (13) no valid standby ref & (main ref invalid or out of lock >100s) (14) all refs evaluated & at least one ref valid Figure 8: Automatic Mode Control State Diagram. Revision 2.07/Jan 2001 a2001 Semtech Corp 44 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS Electrical Specification Important Note: The "Absolute Maximum Ratings" are stress ratings only, and functional operation of the device at conditions other than those indicated in the "Operating Conditions" sections of this specification are not implied. Exposure to the absolute maximum ratings for an extended period may reduce the reliability or useful lifetime of the product. ABSOLUTE MAXIMUM RATINGS PA RA MET ER Sup p ly Voltage V DD, V D+, V A1+,V A2+ Inp ut Voltage (non-sup p ly p ins) Outp ut Voltage (non-sup p ly p ins) A mb ient Op erating Temp erature Range Storage Temp erature FINAL SYM B OL V DD V in Vout TA Tstor MIN -0.5 -40 -50 MA X 3.6 5.5 5.5 85 150 U N IT S V V V C C OPERATING CONDITIONS PA RA MET ER Pow er Sup p ly (d c voltage) V DD, V D+,VA 1+, VA 2+, VA MI+, V DD_DIFF Pow er Sup p ly (d c voltage) V DD5 A mb ient temp erature Range (Typ ical - one 19 MHz outp ut) SYM B OL V DD MIN 3.0 T YP 3.3 MA X 3.6 U N IT S V V DD5 TA IDD PTOT 3.0 -40 - 3.3/5.0 110 360 5.5 85 200 720 V C mA mW Sup p ly current Total p ow er d issip ation DC CHARACTERISTICS: TTL Input pad. Across operating conditions, unless otherwise stated PA R A M E T E R V in High Vin Low Inp ut current SYM B OL V ih V il Ii n MIN 2.0 45 T YP - MA X 0.8 10 U N IT S V V A www.semtech.com Revision 2.07/Jan 2001 a2001 Semtech Corp ACS8510 SETS ADVANCED COMMUNCIATIONS DC CHARACTERISTICS: TTL Input pad with internal pull-up. Across operating conditions, unless otherwise stated FINAL PA R A M E T E R V in High Vin Low Pull-up resistor Inp ut current SYM B OL V ih V il PU Ii n MIN 2.0 30 - T YP - MA X 0.8 80 120 U N IT S V V kW A DC CHARACTERISTICS: TTL Input pad with internal pull-down. Across operating conditions, unless otherwise stated PA R A M E T E R V in High Vin Low Pull-ud ow n resistor Inp ut current SYM B OL V ih V il PD Ii n MIN 2.0 30 - T YP - MA X 0.8 80 120 U N IT S V V kW A DC CHARACTERISTICS: TTL Output pad. Across operating conditions, unless otherwise stated PA R A M E T E R Vout Low Iol = 4mA Vout High Ioh = 4mA Drive current SYM B OL Vol Voh ID MIN 0 2.4 - T YP - MA X 0.4 U N IT S V V 4 mA Revision 2.07/Jan 2001 a2001 Semtech Corp 46 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS DC CHARACTERISTICS: PECL Input/Output pad. Across operating conditions, unless otherwise stated FINAL PA R A M E T E R PECL Inp ut Low voltage Differential inp uts (N ote 1) Differential inp uts (N ote 1) SYM B OL V ILPECL V IHPECL V IDPECL V ILPECL_S V IHPECL_S IIHPECL MIN V DD-2.5 V DD-2.4 0.1 V DD-2.4 V DD-1.3 T YP - MA X V DD-0.5 V DD-0.4 1.4 V DD-1.5 V DD-0.5 U N IT S V V V V V PECL Inp ut High voltage Inp ut Differential voltage PECL Inp ut Low voltage Single end ed inp ut (N ote 2) Single end ed inp ut (N ote 2) PECL Inp ut High voltage Inp ut High current Inp ut d ifferential voltage V ID = 1.4v Inp ut d ifferential voltage V ID = 1.4v (N ote 3) (N ote 3) -10 - +10 A Inp ut Low current IILPECL V OLPECL V OHPECL V ODPECL -10 - +10 A PECL Outp ut Low voltage PECL Outp ut High voltage PECL Outp ut Differential voltage (N ote 1) V DD-2.10 V DD-1.25 580 - V DD-1.62 V DD-0.88 900 V V mV Notes: Unused differential input ports should be left floating and set in LVDS mode, or the positive and negative inputs tied to VDD and GND respectively. Note 1. Assuming a differential input voltage of at least 100 mV. Note 2. Unused differential input terminated to VDD-1.4v. Note 3. With 50W load on each pin to VDD-2v. i.e. 82W to GND and 130W to VDD. Revision 2.07/Jan 2001 a2001 Semtech Corp 47 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS V DD 130R 130R ZO=50 ZO=50 FINAL V DD 8kHz, 1.544/2.048, 6.48, 19.44, 38.88, 51.84, 77.76 or 155.52 MHz I5POS ZO=50 82R 130R T06POS ZO=50 82R 130R 19.44, 38.88, 155.52, 311.04 MHz & DIG1 I5NEG 82R T06NEG 82R GND GND V DD 130R 130R ZO=50 ZO=50 V DD 8kHz, 1.544/2.048, 6.48, 19.44, 38.88, 51.84, 77.76 or 155.52 MHz I6POS ZO=50 82R 130R T07POS ZO=50 82R 130R 19.44, 51.84, 77.76, 155.52 MHz I6NEG 82R T07NEG 82R GND GND Recommended line termination for PECL Input/Output ports for VDD = 3.3V DC CHARACTERISTICS: LVDS Input/Output pad. Across operating conditions, unless otherwise stated PA R A M E T E R LV DS Inp ut voltage range Differential inp ut voltage = 100 mV SYM B OL V VRLVDS VDITH VIDLVDS MIN 0 -100 0.1 T YP - MA X 2.40 +100 1.4 U N IT S V mV V LV DS Differential inp ut th resh old LV DS Inp ut Differential voltage LV DS Inp ut termination resistance Must b e p laced externally across th e LV DS+/- inp ut p ins of A CS8510. Resistor sh ould b e 100W w ith 5% tolerance (N ote 1) (N ote 1) (N ote 1) R T E RM 95 100 105 W LV DS Outp ut h igh voltage LV DS Outp ut low voltage LV DS Differential outp ut voltage LV DS Ch arge in magnitud e of d ifferential outp ut voltage for comp limentary states (N ote 1) V OHLVDS V OLLVDS V ODLVDS 0.885 250 - 1.585 450 V V mV V DOSLVDS - - 25 mV LV DS outp ut offset voltage Temp erature = 25C (N ote 1) V OSLVDS 1.125 - 1.275 V Note 1. With 100W load between the differential outputs. Revision 2.07/Jan 2001 a2001 Semtech Corp 48 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS FINAL 8kHz, 1.544/2.048, 6.48, 19.44, 38.88, 51.84, 77.76 or 155.52 MHz ZO=50 ZO=50 I5POS ZO=50 100R T06POS ZO=50 100R 19.44, 38.88, 155.52, 311.04 MHz & DIG1 I5NEG T06NEG 8kHz, 1.544/2.048, 6.48, 19.44, 38.88, 51.84, 77.76 or 155.52 MHz ZO=50 ZO=50 I6POS ZO=50 100R T07POS ZO=50 100R 19.44, 51.84, 77.76, 155.52 MHz I6NEG T07NEG Recommended line termination for LVDS Input/Output ports Across operating conditions, unless otherwise stated DC CHARACTERISTICS: AMI Input/Output pad. The Alternate Mark Inversion (AMI) signal is DC balanced and consists of positive and negative pulses with a peak to peak voltage of 2.0 +/- 0.2V. The electrical specifications are taken from option a) of Table 2/G.703 - Digital 64kbit/s centralized clock interface, from ITU G.703. PA R A M E T E R Pulse sh ap e N ominal test load imp ed ence Peak voltage of a "mark" (p ulse) Peak value of a "sp ace" N ominal p ulse w id th T IMIN G N ominally rectangular, w ith rise and fall times < 1 s 110 Oh ms 1.0 +/- 0.1V 0.0 +/- 0.1V 7.8 s The electrical characteristics of 64kbits/s interface are as follows; Nominal bit rate: 64kbit/s. The tolerance is determined by the network clock stability. There should be a symmetrical pair carrying the composite timing signal (64kHz and 8kHz). The use of transformers is recommended. Over-voltage protection requirement; refer to Recommendation K.41. Code conversion rules; The data signals are coded in AMI code with 100% duty cycle. The composite clock timing signals convey the 64kHz bit-timing information using AMI coding with a 50% to 70% duty ratio and the 8kHz octet phase information by introducing violations in the code rule. The structure of the signals and voltage levels are shown in Figure 9 and Figure 10. Revision 2.07/Jan 2001 a2001 Semtech Corp 49 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS FINAL 15.6us +1.0VIH 1V 2Vp-p 0VIM 1V 7.8us -1.0VIL Figure 9: Signal structure of 64 kHz/8 kHz central clock interface after suitable input/output transformer (also see Figure 6/G.703). Signal structure of 64 kHz/ 8 kHz central clock interface after suitable transformer. 15.6us 7.8us +VDD 15.6us +1.0VIH 1V 2Vp-p 0VIM 1V 7.8us 0V I_1 C1 TO8POS C2 15.6us -1.0VIL I_2 C1 TO8NEG +VDD 7.8us 0V Figure 10: AMI input and output signal levels. Revision 2.07/Jan 2001 a2001 Semtech Corp 50 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS FINAL AMI input signal Turns ratio 1:1 AMI output signal to external devices AMI input signal C1 TO8NEG GND NOTE: For 1:1 turn ratio, a 3:1 potential divider R load is required to give AMI output with 1 V pp for positive and negative pulses. Recommended line termination for AMI Input/Output ports The AMI inputs Revision 2.07/Jan 2001 a2001 Semtech Corp 51 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS DC CHARACTERISTICS: Output Jitter Generation Across operating conditions, unless otherwise stated FINAL Output jitter generation measured over 60 seconds interval, UI pp max measured using Vectron 6664 12.8MHz TCXO on ICT Flexacom + 10MHz reference from Wavetek 905. U I m e asu r e m e n t o n A C S 8510 R ev 2 0.058 (N ote 2) 0.048 (N ote 3) 0.048 (N ote 2) 0.053 (N ote 4) 0.053 (N ote 5) 0.058 (N ote 6) 0.053 (N ote 7) 0.053 (N ote 2) 0.058 (N ote 3) 0.057 (N ote 8) 0.055 (N ote 9) 0.057 (N ote 10) 0.057 (N ote 11) 0.057 (N ote 12) 0.053 (N ote 13) G813 & G812 for 2.048 MHz op tion 1 20 Hz to 100 kHz UIpp = 0.05 0.046 (N ote 14) Te s t d e f i n i t i o n G813 for 155.52 MHz op tion 1 G813 for 155.52 MHz op tion 1 F i l t e r u se d 500 Hz to 1.3 MHz 65 kHz to 1.3 MHz U I sp e c UIpp = 0.5 UIpp = 0.1 G813 for 155.52 MHz op tion 2 12 kHz to 1.3 MHz UIpp = 0.1 Te s t d e f i n i t i o n G812 for 1.544 MHz G812 for 155.52 MHz electrical G812 for 2.048 MHz electrical F i l t e r u se d 10 Hz to 40 kHz 500 Hz to 1.3 MHz 65 kHz to 1.3 MHz U I sp e c UIpp = 0.05 UIpp = 0.5 U Ip p = 0.075 U I m e asu r e m e n t o n A C S 8510 R ev 2 0.036 (N ote 14) 0.058 (N ote 15) 0.048 (N ote 15) Revision 2.07/Jan 2001 a2001 Semtech Corp 52 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS Te s t d e f i n i t i o n ETS-300-462-3 for 2.048 MHz SEC ETS-300-462-3 for 2.048 MHz SEC (Filter sp ec 49 Hz to 100 kHz) ETS-300-462-3 for 2.048 MHz SSU ETS-300-462-3 for 155.52 MHz ETS-300-462-3 for 155.52 MHz F i l t e r u se d 20 Hz to 100 kHz U I sp e c UIpp = 0.5 FINAL U I m e asu r e m e n t o n A C S 8510 R ev 2 0.046 (N ote 14) 20 Hz to 100 kHz UIpp = 0.2 0.046 (N ote 14) 20 Hz to 100 kHz 500 Hz to 1.3 MHz 65 kHz to 1.3 MHz UIpp = 0.05 UIpp = 0.5 UIpp = 0.1 0.046 (N ote 14) 0.058 (N ote 15) 0.048 (N ote 15) Te s t d e f i n i t i o n GR-253-CORE net i/f, 51.84 MHz GR-253-CORE net i/f, 51.84 MHz (Filter sp ec 20 kHz to 400 kHz) GR-253-CORE net i/f, 155.52 MHz GR-253-CORE net i/f, 155.52 MHz GR-253-CORE cat II elect i/f, 155.52 MHz F i l t e r u se d 100 Hz to 400 kHz U I sp e c UIpp = 1.5 U I m easu r em en t on A C S 8510 R ev 2 0.022 (N ote 15) 18 kHz to 400 kHz UIpp = 0.15 0.019 (N ote 15) 500 Hz to 1.3 MHz 65 kHz to 1.3 MHz UIpp = 1.5 UIpp = 0.15 UIpp = 0.1 UIrms = 0.01 UIpp = 0.1 UIrms = 0.01 UIpp = 0.1 UIrms = 0.01 0.058 (N ote 15) 0.048 (N ote 15) 0.057 (N ote 15) 0.006 (N ote 15) 0.017 (N ote 15) 0.003 (N ote 15) 0.036 (N ote 14) 0.0055 (N ote 14) www.semtech.com 12 kHz to 400 kHz GR-253-CORE cat II elect i/f, 51.84 MHz 12 kHz to 1.3 MHz GR-253-CORE DS1 i/f, 1.544 MHz 10 Hz to 40 kHz Revision 2.07/Jan 2001 a2001 Semtech Corp 53 ACS8510 SETS ADVANCED COMMUNCIATIONS Te s t d e f i n i t i o n AT&T 62411 for 1.544 MHz (Filter sp ec 10 Hz to 8 kHz) AT&T 62411 for 1.544 MHz AT&T 62411 for 1.544 MHz AT&T 62411 for 1.544 MHz F i l t e r u se d 10 Hz to 40 kHz 10 Hz to 40 kHz 10 Hz to 40 kHz Broad b and U I sp e c UIrms = 0.02 UIrms = 0.025 UIrms = 0.025 UIrms = 0.05 FINAL U I m e asu r e m e n t o n A C S 8510 R ev 2 0.0055 (N ote 14) 0.0055 (N ote 14) 0.0055 (N ote 14) 0.0055 (N ote 14) Te s t d e f i n i t i o n G-742 for 2.048 MHz G-742 for 2.048 MHz (Filter sp ec 18 kHz to 100 kHz) G-742 for 2.048 MHz F i l t e r u se d DC to 100 kHz 20 Hz to 100 kHz 20 Hz to 100 kHz U I sp ec UIpp = 0.25 UIpp = 0.05 UIpp = 0.05 U I m easu r em en t on A C S 8510 R ev 2 0.047 (N ote 14) 0.046 (N ote 14) 0.046 (N ote 14) Te s t d e f i n i t i o n TR-N WT-000499 & G824 for 1.544 MHz TR-N WT-000499 & G824 for 1.544 MHz (Filter sp ec 8 kHz to 40 kHz) F i l t e r u se d 10 Hz to 40 kHz U I sp e c UIpp = 5.0 U I m easu r em en t on A C S 8510 R ev 2 0.036 (N ote 14) 10 Hz to 40 kHz UIpp = 0.1 0.036 (N ote 14) Te s t d e f i n i t i o n GR-1244-CORE for 1.544 MHz F i l t e r u se d >10 Hz U I sp e c UIpp = 0.05 U I m e asu r e m e n t o n A C S 8510 R ev 2 0.036 (N ote 14) Revision 2.07/Jan 2001 a2001 Semtech Corp 54 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS Notes for the output jitter generation tables Note 1. Note 2. Note 3. Note 4. Note 5. Note 6. Note 7. Note 8. Note 9. Note 10. Note 11. Note 12. Note 13. Note 14. Note 15. Filter used is that defined by test definition unless otherwise stated 5 Hz bandwidth, 19.44 MHz direct lock 5 Hz bandwidth, 8 kHz lock 20 Hz bandwidth, 19.44 MHz direct lock 20 Hz bandwidth, 8 kHz lock 10 Hz bandwidth, 19.44 MHz direct lock 10 Hz bandwidth, 8 kHz lock 2.5 Hz bandwidth, 19.44 MHz direct lock 2.5 Hz bandwidth, 8 kHz lock 1.2 Hz bandwidth, 19.44 MHz direct lock 1.2 Hz bandwidth, 8 kHz lock 0.6 Hz bandwidth, 19.44 MHz direct lock 0.6 Hz bandwidth, 8 kHz lock 5 Hz bandwidth, 8 kHz lock, 2.048 MHz input 5 Hz bandwidth, 8 kHz lock, 19.44 MHz input FINAL JTAG Timing t CYC TCK t S UR t HT TM S TDI t D OD TDO PA R A M E T E R Cycle time TMS/TDI to TCK rising edge t i me TCK rising to TMS/TDI hold t i me TCK falling to TDO valid SYM B OL tCYC tSUR tHT tDOD MIN 50 3 23 55 T YP - MA X 5 U N IT S ns ns ns ns www.semtech.com Revision 2.07/Jan 2001 a2001 Semtech Corp ACS8510 SETS ADVANCED COMMUNCIATIONS Microprocessor interface timing MOTOROLA Mode In MOTOROLA mode, the device is configured to interface with a microprocessor using a 680x0 type bus. The following figures show the timing diagrams of write and read accesses for this mode. t pw1 FINAL CSB t su2 t h2 X t su1 t h1 WRB X A X address t d1 t d3 data t d2 t pw2 t h3 t d4 X AD Z Z RDY (DTACK) S y m b ol tsu1 tsu2 td 1 td 2 td 3 td 4 tp w 1 tp w 2 th 1 th 2 th 3 tp Z Z P ar am e t e r Setup A valid to CSBfalling edge Setup WRB valid to CSBfalling edge Delay CSBfalling edge to AD valid Delay CSBfalling edge to DTACKrising edge Delay CSBrising edge to AD high-Z Delay CSBrising edge to RDY high-Z CSB low time DTACK high time Hold A valid after CSBrising edge Hold WRB high after CSBrising edge Hold CSB low after DTACKfalling edge Time b etw een consecutive accesses (CSBrising edge to CSBfalling edge) MIN 0 ns 0 ns 485 ns(1) 310 ns 3 ns 0 ns 0 ns 320 ns T YP - MA X 177 ns 13 ns 0 ns 7 ns 472 ns - Read access timing in MOTOROLA Mode. Note 1: Timing with RDY. If RDY not used, tpw1 becomes 178 ns. Revision 2.07/Jan 2001 a2001 Semtech Corp 56 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS FINAL t pw1 CSB t su2 t h2 X t su1 t h1 WRB X A X address t su3 t h4 X AD X t d2 t pw2 data t h3 t d4 X RDY (DTACK) Z Z S y m b ol tsu1 tsu2 tsu3 td 2 td 4 tp w 1 tp w 2 th 1 th 2 th 3 th 4 tp Setup A valid to CSBfalling edge P ar am e t e r MIN 0 ns 0 ns 3 ns 485 ns(1) 310 ns 3 ns 0 ns 0 ns 4 ns 320 ns T YP - MA X 13 ns 7 ns 472 ns - Setup WRB valid to CSBfalling edge Setup AD valid b efore CSBrising edge Delay CSBfalling edge to DTACKrising edge Delay CSBrising edge to RDY high-Z CSB low time DTACK high time Hold A valid after CSBrising edge Hold WRB low after CSBrising edge Hold CSB low after DTACKfalling edge Hold AD valid after CSBrising edge Time b etw een consecutive accesses (CSBrising edge to CSBfalling edge) - - Write access timing in MOTOROLA Mode. Note 1: Timing with RDY. If RDY not used, tpw1 becomes 178 ns. Revision 2.07/Jan 2001 a2001 Semtech Corp 57 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS INTEL Mode In INTEL mode, the device is configured to interface with a microprocessor using a 80x86 type bus. The following figures show the timing diagrams of write and read accesses for this mode. FINAL CSB WRB t su2 t pw 1 t h2 RDB t su1 t h1 a d dre ss t d1 t d4 d ata t d2 t d3 t pw2 t h3 t d5 Z Z A AD Z RDY Z S y m b ol tsu1 tsu2 td 1 td 2 td 3 td 4 td 5 tp w 1 tp w 2 th 1 th 2 th 3 tp Setup A valid to CSBfalling edge P ar am e t e r MIN 0 ns 0 ns - T YP - MA X 177 ns 13 ns 14 ns 10 ns 9 ns Setup CSBfalling edge to RDBfalling edge Delay RDBfalling edge to A D valid Delay CSBfalling edge to RDY active Delay RDBrising edge to RDYfalling edge Delay RDBrising edge to A D h igh -Z Delay CSBrising edge to RDY h igh -Z RDB low time RDY low time Hold A valid after RDBrising edge Hold CSB low after RDBrising edge Hold RDB low after RDYrising edge Time b etw een consecutive accesses (RDBrising edge to RDBfalling edge , or RDBrising edge to WRBfalling edge) 486 ns(1) 310 ns 0 ns 0 ns 0 ns 320 ns - 472 ns - Read access timing in INTEL Mode. Note 1: Timing with RDY. If RDY not used, tpw1 becomes 180 ns. Revision 2.07/Jan 2001 a2001 Semtech Corp 58 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS FINAL CSB t su2 t pw1 t h2 WRB RDB t su1 t h1 address t su3 t h4 A AD t d2 t d3 t pw2 data t h3 t d5 Z RDY Z Sy m b ol tsu1 tsu2 tsu3 td 2 td 3 td 5 tp w 1 tp w 2 th 1 th 2 th 3 th 4 tp Setup A valid to CSBfalling edge P ar am e t e r MIN 0 ns 0 ns 3 ns - T YP - MA X 13 ns 14 ns 9 ns Setup CSBfalling edge to WRBfalling edge Setup A D valid to WRBrising edge Delay CSBfalling edge to RDY active Delay WRBfalling edge to RDYfalling edge Delay CSBrising edge to RDY h igh -Z WRB low time RDY low time Hold A valid after WRBrising edge Hold CSB low after WRBrising edge Hold WRB low after RDYrising edge Hold A D valid after WRBrising edge Time b etw een consecutive accesses (WRBrising edge to WRBfalling edge , or WRBrising edge to RDBfalling edge) 486 ns(1) 310 ns 170 ns(2) 0 ns 0 ns 4 ns 320 ns - 472 ns - - - Write access timing in INTEL Mode. Note 1: Timing with RDY. If RDY not used, tpw1 becomes 180 ns. Note 2: Timing if th2 is greater than 170 ns, otherwise 5 ns after CSB rising edge. Revision 2.07/Jan 2001 a2001 Semtech Corp 59 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS MULTIPLEXED Mode In MULTIPLEXED mode, the device is configured to interface with a microprocessor using a multiplexed address/ data bus. The following figures show the timing diagrams of write and read accesses for this mode. t pw 3 FINAL t p1 ALE t su1 t h1 CSB t su2 WRB t pw 1 t h2 RDB t d1 t d a ta d4 AD a d d re s s t X t X t t d2 d3 t pw 2 h3 d5 RDY Z Z S y m b ol tsu1 tsu2 td 1 td 2 td 3 td 4 td 5 tp w 1 tp w 2 tp w 3 th 1 th 2 th 3 tp 1 tp 2 P ar am e t e r Setup A D ad d ress valid to A LEfalling edge Setup CSBfalling edge to RDBfalling edge Delay RDBfalling edge to A D d ata valid Delay CSBfalling edge to RDY active Delay RDBfalling edge to RDYfalling edge Delay RDBrising edge to A D d ata h igh -Z Delay CSBrising edge to RDY h igh -Z RDB low time RDY low time A LE h i gh t i me Hold A D ad d ress valid after A LEfalling edge Hold CSB low after RDBrising edge Hold RDB low after RDYrising edge Time b etw een A LEfalling edge and RDBfalling edge Time b etw een consecutive accesses (RDBrising edge to A LErising edge) MIN 2 ns 0 ns 487 ns (1) T YP - MA X 177 ns 13 ns 15 ns 9 ns 10 ns 472 ns 310 ns 2 ns 3 ns 0 ns 0 ns 0 ns 320 ns - - Read access timing in MULTIPLEXED Mode. Note 1: Timing with RDY. If RDY not used, tpw1 becomes 180 ns. Revision 2.07/Jan 2001 a2001 Semtech Corp 60 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS t pw 3 FINAL t p1 ALE t su1 t h1 CSB t su 2 t pw 1 t h2 W RB RDB t su3 t h4 AD a d d re s s t X t d a ta t t t X d2 d3 pw 2 h3 d5 RDY Z Z Sy m b ol tsu1 tsu2 tsu3 td 2 td 3 td 5 tp w 1 tp w 2 tp w 3 th 1 th 2 th 3 th 4 tp 1 tp 2 P ar am e t e r Setup A D ad d ress valid to A LEfalling edge Setup CSBfalling edge to WRBfalling edge Setup A D d ata valid to WRBrising edge Delay CSBfalling edge to RDY active Delay WRBfalling edge to RDYfalling edge Delay CSBrising edge to RDY h igh -Z WRB low time RDY low time A LE h i gh t i me Hold A D ad d ress valid after A LEfalling edge Hold CSB low after WRBrising edge Hold WRB low after RDYrising edge A D d ata h old valid after WRBrising edge Time b etw een A LEfalling edge and WRBfalling edge Time b etw een consecutive accesses (WRBrising edge to A LErising edge) MIN 2 ns 0 ns 3 ns - T YP - MA X 13 ns 15 ns 9 ns 487 ns(1) 310 ns 2 ns 3 ns 0 ns 0 ns 4 ns 0 ns 320 ns - 472 ns - - - Write access timing in MULTIPLEXED Mode. Note 1: Timing with RDY. If RDY not used, tpw1 becomes 180 ns. Revision 2.07/Jan 2001 a2001 Semtech Corp 61 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS SERIAL Mode In SERIAL mode, the device is configured to interface with a serial microprocessor bus. The following figures show the timing diagrams of write and read accesses for this mode. During read access the output data SDO (AD(0)) is clocked out on the rising edge of SCLK (ALE) when the active edge selection control bit CLKE (A(1)) is 0 and on the falling edge when CLKE = 1. Address, read/write control bit and write data are always clocked into the interface on the rising edge of SCLK. Both input data SDI and clock SCLK are oversampled, filtered and synchronized to the 6MHz internal clock. The serial interface clock (SCLK) is not required to run between accesses (i.e., when CSB = 1). FINAL CLKE = 0; SDO data is clocked out on the rising edge of SCLK CSB t su2 t pw2 t h2 ALE=SCLK t su1 t h1 _ R/W t pw1 A(0)=SDI A0 A1 A2 A3 A4 A5 A6 t d1 t d2 AD(0)=SDO CLKE = 1; SDO data is clocked out on the falling edge of SCLK D0 D1 D2 D3 D4 D5 D6 D7 CSB t h2 ALE=SCLK A(0)=SDI _ R/W A0 A1 A2 A3 A4 A5 A6 t d1 t d2 D0 D1 D2 D3 D4 D5 D6 D7 AD(0)=SDO Read access timing in SERIAL Mode. Revision 2.07/Jan 2001 a2001 Semtech Corp 62 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS S y m b ol tsu1 tsu2 td 1 td 2 tp w 1 tp w 2 th 1 th 2 tp P ar am e t e r Setup SDI valid to SCLKrising edge Setup CSBfalling edge to SCLKrising edge Delay SCLKrising edge (SCLKfalling edge for CLKE = 1)to SDO valid Delay CSBrising edge to SDO h igh -Z SCLK low time SCLK h igh time Hold SDI valid after SCLKrising edge Hold CSB low after SCLKrising edge, for CLKE = 0 Hold CSB low after SCLKfalling edge, for CLKE = 1 Time b etw een consecutive accesses (CSBrising edge to CSBfalling edge) MIN 0 ns 160 ns 180 ns 180 ns 170 ns 5 ns 160 ns T YP - FINAL MA X 17 ns 10 ns - Read access timing in SERIAL Mode. CSB t su2 t pw2 t h2 ALE=SCLK t su1 t h1 _ R/W t pw1 A(0)=SDI A0 A1 A2 A3 A4 A5 A6 D0 D1 D2 D3 D4 D5 D6 D7 D(0)=SDO S y m b ol tsu1 tsu2 tp w 1 tp w 2 th 1 th 2 tp P ar am e t e r Setup SDI valid to SCLKrising edge Setup CSBfalling edge to SCLKrising edge SCLK low time SCLK high time Hold SDI valid after SCLKrising edge Hold CSB low after SCLKrising edge Time betw een consecutive accesses (CSBrising edge to CSBfalling edge) MIN 0 ns 160 ns 180 ns 180 ns 170 ns 5 ns 160 ns T YP - MA X - Write access timing in SERIAL Mode. Revision 2.07/Jan 2001 a2001 Semtech Corp 63 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS EPROM Mode In EPROM mode, the ACS8510 takes control of the bus as Master, and reads the device set-up from an AMD AM27C64 type EPROM at lowest speed (250ns), after device start-up (system reset). The EPROM access state machine in the up interface sequences the accesses. Further details can be found in the AMD AM27C64 data sheet. FINAL CSB (=OEB) A address t acc AD Z data Z S y m b ol tacc P ar am e t e r Delay CSBfalling edge or A change to AD valid MIN - T YP - MA X 920 ns Read access timing in EPROM Mode. Revision 2.07/Jan 2001 a2001 Semtech Corp 64 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS Package information FINAL D 2 3 D1 1 AN2 AN3 1 R1 S E 2 E1 1 3 4 L1 A A AN1 B R2 B Section A-A AN4 L 123 5 b e 7 Section B-B A A2 c 7 c1 7 Seating plane A1 6 b b1 7 8 Notes 1 2 3 The top package body may be smaller than the bottom package body by as much as 0.15 mm. To be determined at seating plane. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is 0.25 mm per side. D1 and E1 are maximum plastic body size dimensions including mold mismatch. Details of pin 1 identifier are optional but will be located within the zone indicated. Exact shape of corners can vary. A1 is defined as the distance from the seating plane to the lowest point of the package body. These dimensions apply to the flat section of the lead between 0.10 mm and 0.25 mm from the lead tip. Shows plating. 4 5 6 7 8 Revision 2.07/Jan 2001 a2001 Semtech Corp 65 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS 100 L Q F P P ac k ag e D i m e n si o n s in mm FINAL D/E D 1/ E 1 A A1 A2 e AN1 AN2 AN3 AN4 R1 R2 L L1 S b b1 c c1 Mi n N om Max 16.00 14.00 1.40 0.05 1.50 1.60 0.10 0.15 1.35 1.40 1.45 0.50 11 12 13 11 12 13 0 - 0 3.5 7 0.08 - 0.08 0.20 0.45 0.60 0.75 1.00 (ref) 0.20 - 0.17 0.22 0.27 0.17 0.20 0.23 0.09 0.20 0.09 0.16 Thermal conditions The device is rated for full temperature range when this package is used with a 4 layer or more PCB. Copper coverage must exceed 50%. All pins must be soldered to the PCB. Maximum operating temperature must be reduced when the device is used with a PCB with less than these requirements. Notes Revision 2.07/Jan 2001 a2001 Semtech Corp 66 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS Application information A simplified Application Schematic for the ACS8510 is illustrated in Figure 11. FINAL Typical power supply VDD P1 5v 0v term_connect (+) ZD1 ZD1 C2 VDD5v IC2 3 VIN 1 GND VOUT L1 L2 L3 VDD3 VDDA 2 EZ1086 100uF 100nF C3 (+) C4 10uF_TANT VDD2 10uF_TANT (+) L4 C5 L5 L6 DGND3 C6 100nF DGND2 C7 100nF Optional Processor interface AGND Int ALE WRB SrcSwit RDY RDB CSB DGND VDD O1 O2 O3 O4 O5 O9 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 AD(7) AD(6) AD(5) AD(4) AD(3) AD(2) AD(1) AD(0) VSSc VDDc VDDb VSSb O1 O2 O3 VDDa VSSa O4 O5 O9 TSCAN TEST1 TEST2 MSTSLVB SDHB 100nF C9 Optional boot EPROM DGND AD[0:7] 14 28 11 12 13 15 16 17 18 19 GND Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 DGND C1 100nF VDD5v Am27c64 IC3 VCC A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 VDD DGND CE_B 20 OE_B 22 P_B 27 AGND X1 2 vdd output 1 _txco gnd2 5 12.8MHz optn 4 VDDA R1 10R R7 10R C12 100nF AGND VDD3 C11 100nF DGND3 C10 100nF 3 gnd1 DGND 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 VDD(AMI) O8NEG O8POS GND(AMI) O10 O11 VSS_DIFFa VDD_DIFFa O6POS O6NEG O7POS O7NEG VSS_DIFFb VDD_DIFFb I5POS I5NEG I6POS I6NEG VDD5 SYNC2K I3 I4 I7 VSSe VDDe 1 GND(GR) 2 BSMODE 3 IREF1 4 NC 5 GND(A1) 6 VA1+ 7 TMS 8 Int 9 TCK 10 REFCLK 11 GND(D1) 12 VD+(D1) 13 VD+(D3) 14 GND(D3) 15 GND(D2) 16 VD+(D2) 17 NC 18 SrcSwit 19 VA2+ 20 GND(A2) 21 TDO 22 IREF2 23 TDI 24 I1 25 I2 IC1 ACS8510 RDY 75 PORB 74 ALE 73 RDB 72 WRB 71 CSB 70 A(0) 69 A(1) 68 A(2) 67 A(3) 66 A(4) 65 A(5) 64 A(6) 63 VSSd 62 VDDd 61 UPSEL(0) 60 UPSEL(1) 59 UPSEL(2) 58 I14 57 I13 56 I12 55 I11 54 I10 53 I9 52 I8 51 10 9 8 7 6 5 4 3 25 24 21 23 2 1nF C8 VDD DGND DGND A[0:7] VDD 100nF C13 DGND Optional Processor interface type selection VDD C14 100nF C21 440pF C20 100nF 6 7 5 8 VDD VDD2 DGND C15 100nF C16 470nF C17 470nF 2nF C22 DGND DGND2 I1 I2 O8 O10 O11 DGND2 O6P O6N O7P O7N I5P I5N I6P I6N SYNC2K I3 I4 I7 I8 I9 I10 I11 I12 I13 I14 DGND DGND Figure 11: A simplified Application Schematic. Revision 2.07/Jan 2001 a2001 Semtech Corp 67 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS Revision History Changes from revision 2.06 to 2.07. January 2001. I t em 1 2 3 4 5 6 7 8 9 10 11 S e ct i o n Tab le of contents Pin descrip tions Tab le 5 Register descrip tion Register descrip tion Register descrip tion Register descrip tion Register descrip tion Leaky b ucket timing b ox Holdover mode Revision History P ag e 2 5 15 25 26 28 28 31 36 39 68 Inclusion of Revision History Pins 34/35 and 36/37 corrected for LVDS/PECL defaults Por ts T06 and T07 corrected for LVDS/PECL defaults sts_interrup ts register re-formatted and address error removed sts_curr_inc_offset register corrected for errors cnfg_sts_remote_sources_valid register re-formatted cnfg_op erating_mode register error corrected cnfg_freq_limit register re-formatted and re-w ritten Omission corrected in default setting equation Sp elling error corrected Section added D e scr i p t i o n FINAL Revision 2.07/Jan 2001 a2001 Semtech Corp 68 www.semtech.com ACS8510 SETS ADVANCED COMMUNCIATIONS Ordering information FINAL PA R T N U M B E R A CS8510 DE SCR I P T I O N SON ET/SDH Synch ronisation, 100 p in LQFP Disclaimers Life support - This product is not designed or intended for use in life suport equipment, devices or systems, or other critical applications. This product is not authorized or warranted by Semtech Corporation for such use. Right to change - Semtech Corporation reserves the right to make changes, without notice, to this product. Customers are advised to obtain the latest version of the relevant information before placing orders. For additional information, contact the following: Semtech Corporation Advanced Communications Products E-Mail: Internet: USA: AdvCom@semtech.com http://www.semtech.com 652 Mitchell Road, Newbury Park, CA 91320-2289 Tel: +1 805 498 2111, Fax: +1 805 498 3804 FAR EAST: 11F, No. 46, Lane 11, Kuang Fu North Road, Taipei, Taiwan, R.O.C. Tel: +886 2 2748 3380, Fax: +886 2 2748 3390 EUROPE: Delta House, Chilworth Science Park, Southampton, Hants, SO16 7NS, UK Tel: +44 23 80 769008, Fax: +44 23 80 768612 ISO9001 CERTIFIED Revision 2.07/Jan 2001 a2001 Semtech Corp 69 www.semtech.com |
Price & Availability of ACS8510
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |